- 您現在的位置：買賣IC網 > PDF目錄366689 > CAT24C44V-TE13 256-Bit Serial Nonvolatile CMOS Static RAM PDF資料下載
參數資料
| 型號： | CAT24C44V-TE13 |
| 英文描述： | 256-Bit Serial Nonvolatile CMOS Static RAM |
| 中文描述： | 256位串行非易失性的CMOS靜態RAM |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 97K |
| 代理商： | CAT24C44V-TE13 |
CAT24C44
5
Doc. No. 1083, Rev. R
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
DEVICE OPERATION
The CAT24C44 is intended for use with standard micro-
processors. The CAT24C44 is organized as 16 registers
by 16 bits. Seven 8-bit instructions control the device
’
s
operating modes, the RAM reading and writing, and the
EEPROM storing and recalling. It is also possible to
control the EEPROM store and recall functions in hard-
ware with the
STORE
and
RECALL
pins. The CAT24C44
operates on a single 5V supply and will generate, on
chip, the high voltage required during a RAM to EEPROM
storing operation.
Instructions, addresses and write data are clocked into
the DI pin on the rising edge of the clock (SK). The DO
pin remains in a high impedance state except when
outputting data from the device. The
CE
(Chip Enable)
pin must remain high during the entire data transfer.
The format for all instructions sent to the CAT24C44 is
a logical
‘
1
’
start bit, 4 address bits (data read or write
operations) or 4
“
Don
’
t Care
”
bits (device mode opera-
tions), and a 3-bit op code (see Instruction Set). For data
write operations, the 8-bit instruction is followed by 16
bits of data. For data read instructions, DO will come out
of the high impedance state and enable 16 bits of data
to be clocked from the device. The 8th bit of the read
instruction is a
“
Don
’
t Care
”
bit. This is to eliminate any
bus contention that would occur in applications where
the DI and DO pins are tied together to form a common
DI/DO line. A word of caution while clocking data to and
from the device: If the
CE
pin is prematurely deselected
while shifting in an instruction, that instruction will not be
executed, and the shift register internal to the CAT24C44
will be cleared. If there are more than or less than 16
clocks during a memory data transfer, an improper data
transfer will result. The SK clock is completely static
allowing the user to stop the clock and restart it to
resume shifting of data.
Read
Upon receiving a start bit, 4 address bits, and the 3-bit
read command (clocked into the DI pin), the DO pin of
the CAT24C44 will come out of the high impedance state
and the 16 bits of data, located at the address specified
in the instructions, will be clocked out of the device.
When clocking data from the device, the first bit clocked
out (DO) is timed from the falling edge of the 8th clock,
all succeeding bits (D1
–
D15) are timed from the rising
edge of the clock.
Write
After receiving a start bit, 4 address bits, and the 3-bit
WRITE command, the 16-bit word is clocked into the
device for storage into the RAM memory location speci-
fied. The
CE
pin must remain high during the entire write
operation.
Figure 1. RAM Read Cycle Timing
Note:
(1) Bit 8 of READ instruction is
“
Don
’
t Care
”
.
Figure 2. RAM Write Cycle Timing
SK
CE
DI
D0
1
2
3
4
5
6
7
8
9
10
11
12
22
23
24
1
D1
D2
D3
D13
D14
D15
A
1
A
1
A
A
0
SK
CE
DI
DO
HIGH-Z
D0
1
2
3
4
5
6
7
8
9
10
11
12
22
23
24
1
D1
D2
D3
D14
D15
D0
A
X
A
1
1
A
A
(8)
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24C64VP2IT3 | 64-Kb I2C CMOS Serial EEPROM |
| CAT24C64WI-GT2 | 64-Kb I2C CMOS Serial EEPROM |
| CAT24C64WI-GT3 | 64-Kb I2C CMOS Serial EEPROM |
| CAT24C64WIT2 | 64-Kb I2C CMOS Serial EEPROM |
| CAT24C64WIT3 | 64-Kb I2C CMOS Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24C512HU5IGT3 | 功能描述:電可擦除可編程只讀存儲器 512KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C512LI-G | 功能描述:電可擦除可編程只讀存儲器 512KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C512WI-G | 制造商:ON Semiconductor 功能描述:512KB I2C SER EEPROM - Rail/Tube 制造商:ON Semiconductor 功能描述:EEPROM 512KB I2C SER EEPROM 制造商:ON Semiconductor 功能描述:TUBE / 512KB I2C SER EEPROM |
| CAT24C512WI-GT3 | 功能描述:電可擦除可編程只讀存儲器 512KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C512XI | 功能描述:電可擦除可編程只讀存儲器 512KB I2C SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。