- 您現在的位置：買賣IC網 > PDF目錄366715 > CAT25C256SA-TE13 64K 8K x 8 Battery-Voltage CMOS E2PROM PDF資料下載
參數資料
| 型號： | CAT25C256SA-TE13 |
| 元件分類： | EEPROM |
| 英文描述： | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| 中文描述： | 64K的8K的× 8電池電壓的CMOS E2PROM的 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 79K |
| 代理商： | CAT25C256SA-TE13 |
7
CAT25C128/256
Doc. No. 25088-00 1/01
After the correct read instruction and address are sent,
the data stored in the memory at the selected address is
shifted out on the SO pin. The data stored in the memory
at the next address can be read sequentially by continu-
ing to provide clock pulses. The internal address pointer
is automatically incremented to the next higher address
after each byte of data is shifted out. When the highest
address (7FFFh for 25C256 and 3FFFh for 25C128) is
reached, the address counter rolls over to 0000h allow-
ing the read cycle to be continued indefinitely. The read
operation is terminated by pulling the
CS
high. To read
the status register, RDSR instruction should be sent.
The contents of the status register are shifted out on the
SO line. The status register may be read at any time
even during a write cycle.Read sequence is illustrated in
figure 4. Reading status register is illustrated in figure 5.
Figure 2. WREN Instruction Timing
Figure 3. WRDI Instruction Timing
DEVICE OPERATION
Write Enable and Disable
The CAT25C128/256 contains a write enable latch. This
latch must be set before any write operation. The device
powers up in a write disable state when V
cc
is applied.
WREN instruction will enable writes (set the latch) to the
device. WRDI instruction will disable writes (reset the
latch) to the device. Disabling writes will protect the
device against inadvertent writes.
READ Sequence
The part is selected by pulling
CS
low. The 8-bit read
instruction is transmitted to the CAT25C128/256, fol-
lowed by the 16-bit address (the Most Significant Bit is
don’t care for 25C256 and the two most significant bits
are don't care for the 25C128).
SK
SI
CS
SO
0
0
0
0
0
1
1
0
HIGH IMPEDANCE
SK
SI
CS
SO
0
0
0
0
0
1
0
0
HIGH IMPEDANCE
Note: Dashed Line= mode (1, 1) — — — —
Note: Dashed Line= mode (1, 1) — — — —
相關PDF資料 |
PDF描述 |
|---|---|
| CAT25C256SI-1.8TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT25C256SI-TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT25C256S-TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT25C256U14A-TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
| CAT25C256U14I-TE13 | 64K 8K x 8 Battery-Voltage CMOS E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT25C256X | 功能描述:電可擦除可編程只讀存儲器 (32kx8) 256K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C256X-1.8 | 功能描述:電可擦除可編程只讀存儲器 (32kx8) 256K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C256XA | 功能描述:電可擦除可編程只讀存儲器 (32kx8) 256K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C256XE-TE13 | 制造商:ON Semiconductor 功能描述:EEPROM Serial-SPI 256K-Bit 32K x 8 3.3V/5V 8-Pin SOIC EIAJ T/R |
| CAT25C256XI | 功能描述:電可擦除可編程只讀存儲器 (32kx8) 256K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。