參數資料
型號: CBTL06122AHF
廠商: NXP Semiconductors N.V.
元件分類: 編、解碼器及復用、解復用
英文描述: High-performance DisplayPort-PCIe Gen2 hex display multiplexer
封裝: CBTL06122AHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1.html<1<Always Pb-free,;CBTL06122BHF<SOT1033-1 (HWQFN56R)|<<http://www.nxp.com/packages/SOT1033-1
文件頁數: 4/19頁
文件大小: 104K
代理商: CBTL06122AHF
CBTL06122_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 16 April 2009
12 of 19
NXP Semiconductors
CBTL06122
High-performance DP/PCIe Gen2 hex display multiplexer
10.4 HPD input, HPD output
[1]
Low-speed input changes state on cable plug/unplug.
[2]
Time from HPD_SINK changing state to HPD changing state. Includes HPD rise/fall time.
10.5 MUX select and latch input
11. Test information
11.1 Switch test xture requirements
The test xture for switch S-parameter measurement shall be designed and built to
specic requirements, as described below, to ensure good measurement quality and
consistency.
The test xture shall be a FR4-based PCB of the microstrip structure; the dielectric
thickness or stack-up shall be about 4 mils.
The total thickness of the test xture PCB shall be 1.57 mm (0.62 in).
The measurement signals shall be launched into the switch from the top of the test
xture, capturing the through-hole stub effect.
Traces between the DUT and measurement ports (SMA or microprobe) should be
uncoupled from each other, as much as possible. Therefore, the traces should be
routed in such a way that traces will diverge from each other exiting from the switch
pin eld.
The trace lengths between the DUT and measurement port shall be minimized. The
maximum trace length shall not exceed 1000 mils. The trace lengths between the
DUT and measurement port shall be equal.
All of the traces on the test board and add-in card must be held to a characteristic
impedance of 50
with a tolerance of ±7%.
SMA connector is recommended for ease of use. The SMA launch structure shall be
designed to minimize the connection discontinuity from SMA to the trace. The
impedance range of the SMA seen from a TDR with a 60 ps rise time should be
within 50
± 7 .
Table 11.
HPD input and output characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VI
input voltage
0.3
-
3.6
V
tPD
propagation delay
from HPD_SINK to HPD_SOURCE
180
-
ps
Table 12.
SEL, LE_N input characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIH
HIGH-level input voltage
SEL/LE_N
2.0
-
3.6
V
VIL
LOW-level input voltage
SEL/LE_N
0
-
0.8
V
ILI
input leakage current
measured with input at
VIH(max) and VIL(min)
--10
A
相關PDF資料
PDF描述
CBTL06122BHF High-performance DisplayPort-PCIe Gen2 hex display multiplexer
CBTL06DP211EE DisplayPort Gen1 2 : 1 multiplexer
CBTL06DP212EE High-performance DisplayPort Gen2 2 : 1 multiplexer
CBTL12131ET DisplayPort multiplexer for bidirectional video in all-in-one computer systems
CBTU04082BS 1.8 V, wide bandwidth, 4 differential channel, 2 : 1 multiplexer-demultiplexer switch with single enable
相關代理商/技術參數
參數描述
CBTL06122AHF,518 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
CBTL06122AHF,518-CUT TAPE 制造商:NXP 功能描述:CBTL06122 Series 6 Channel DisplayPort 1:2 PCI Express GEN2 Multiplexer-HWQFN56R
CBTL06122AHF518 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
CBTL06122AHF-T 功能描述:編碼器、解碼器、復用器和解復用器 GEN1 HEX DISPLAY MULTIPLEXER RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
CBTL06122BHF 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:High-performance DisplayPort/PCIe Gen2 hex display multiplexer