- 您現在的位置：買賣IC網 > PDF目錄1908 > CC-2434K2-CS5 (Copeland Communications Inc)MODEM FAX 33K 5V PDF資料下載
參數資料
| 型號： | CC-2434K2-CS5 |
| 廠商： | Copeland Communications Inc |
| 文件頁數： | 20/62頁 |
| 文件大小： | 0K |
| 描述： | MODEM FAX 33K 5V |
| 標準包裝： | 30 |
| 數據格式： | V.21，V.22，V.23，Bell 103 |
| 波特率： | 33k |
| 電源電壓： | 4.2 V ~ 7 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 模塊 |
| 包裝： | 散裝 |
| 配用： | 539-1002-ND - KIT EVALUATION WORLD MODEM II |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Data Sheet
World Modem FAX
Page 27 of 62
2005, Copeland Communications, Inc.
World Modem FAX Datasheet Rev 1.0
Fax AT Command Set (Command Defaults in Bold)
Command
Action
+FCLASS = N
Fax mode select
n
Mode
0
Data mode
1
Fax class 1 / 1.0 mode
8
Voice mode
+FAE = n
Data/Fax auto answer
If enabled, the modem will automatically distinguish between a voice, data or fax call and issue
either a DATA or FAX result code
n
Mode
0
Data / fax discriminator disabled
1
Data / fax discriminator enabled
+FTS = n
Stop transition and wait for n 10 ms intervals before responding with the OK result code
+FRS = n
Report back to the DTE with an OK result code after n 10 ms intervales of silence have been
detected on the line.
+FTM = n
Transmit Data with carrier n.
+FRM = n
Receive Data with carrier n.
+FTH = n
Transmit Data with HDLC framing and carrier n. Only mandatory carrier, n = 3 supported.
+FRH = n
Receive Data with HDLC framing and carrier n. Only mandatory carrier, n = 3 supported.
+FAR = n
Adaptive reception control.
If enabled, the modem will detect the selected carrier on V.21 control messages. If the expected
carrier is deteced, the modem will operate as specified in the respective +FRM = <mod> or +FRH
= <mod> commands. If the V.21 flag preamble is detected instead, the modem will issue a
+FRH:3 intermediate result code and then execute an implied +FRH = 3 command.
n
Mode
0
Adaptive reception disable
1
Adaptive reception enable
+FCL = <0-255>
Carrier loss timeout in 100 ms increments.
+FDD = n
Double escape character replacement.
n
Decode of <DLE><DUB>
Encoding of <DLE><SUB>
0
<DLE><DLE> or discard
<DLE><DLE><DLE><DLE>
1
<DLE><DLE>
<DLE><SUB>
+FIT = A, B
DTE inactivity timeout
A The inactivity timeout in seconds. Valid range from <0 – 255>. A zero disables the timeout.
B Describes the action taken upon timeout. Valid range <0,1>
0 – Upon timeout, the modem will go on-hook then reset to +FCLASS = 0.
1 - Upon timeout, the modem will only go on-hook.
+FPR = n
DTE rate
n
Mode
0
Select automatic rate detection
1
Set DTE to 2400 bps
2
Set DTE to 4800 bps
3
Set DTE to 9600 bps
4
Set DTE to 19200 bps
8
Set DTE to 38400 bps
10
Set DTE rate to 38400 bps
18
Set DTE rate to 57600 bps
+FMI?
Report Manufacturer ID
+FMM?
Report modem chipset model
+FMR?
Report modem chipset revision
相關PDF資料 |
PDF描述 |
|---|---|
| CC-24K2N-CS5 | MODEM WORLD NET 2400BAUD 5V |
| CC-92K2-IS | MODEM 56KBAUD V.90 SERIAL 3.3V |
| CC-MX-LB69-ZM | CONNECTCORE I.MX51 MODULE |
| CD22M3494MQZ96 | IC CROSSPOINT SWITCH 16X8 44PLCC |
| CD4052BPWRE4 | IC MUX/DEMUX DUAL 4X1 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CC2-4-4/0#4 | 制造商:Thomas & Betts 功能描述:Cable Accessories Exothermic Welding Reusable Graphite Mold |
| CC2-4-4/01/0 | 制造商:Thomas & Betts 功能描述:FURSEWELD MOULDS |
| CC2-4-4/02/0 | 制造商:Thomas & Betts 功能描述:Cable Accessories Exothermic Welding Reusable Graphite Mold |
| CC2-4-4/03/0 | 制造商:Thomas & Betts 功能描述:CABLE TO CABLE - PICTORIAL INDEX |
| CC2-4-4/04/0 | 制造商:Thomas & Betts 功能描述:Cable Accessories Exothermic Welding Reusable Graphite Mold |
發布緊急采購，3分鐘左右您將得到回復。