- 您現在的位置：買賣IC網 > PDF目錄378446 > CH7003B-V (Electronic Theatre Controls, Inc.) Digital PC to TV Encoder PDF資料下載
參數資料
| 型號： | CH7003B-V |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Digital PC to TV Encoder |
| 中文描述： | 數碼電腦電視編碼器 |
| 文件頁數： | 26/50頁 |
| 文件大?。?/td> | 334K |
| 代理商： | CH7003B-V |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
CHRONTEL
CH7003B
26
201-0000-023 Rev.4.1, 8/2/99
Transfer Protocols
(continued)
AutoInc
Register Address Auto-Increment - to facilitate sequential R/W of registers.
“1”:
Auto-Increment enabled (auto-increment mode).
Write: After writing data into a register, the Address Register will automatically be
incremented by one.
Read: Before loading data from a register to the on-chip temporary register (getting ready to
be serially read), the Address Register will automatically be incremented by one.
However, for the first read after an RAB, the Address Register will not be changed.
“0”:
Auto-Increment disabled (alternating mode).
Write: After writing data into a register, the Address Register will remain unchanged until a
new RAB is written.
Read: Before loading data from a register to the on-chip temporary register (getting ready to
be serially read), the Address Register will remain unchanged.
AR[5:0]
Specifies the Address of the Register to be Accessed.
This register address is loaded into the Address Register of the CH7003. The R/W access, which
follows, is directed to the register specified by the content stored in the Address Register.
The following two sections describe the operation of the serial interface for the four combinations of R/W = 0,1 and
AutoInc = 0,1.
CH7003 Write Cycle Protocols (R/W = 0)
Data transfer with acknowledge is required. The acknowledge-related clock pulse is generated by the master-
transmitter. The master-transmitter releases the SD line (HIGH) during the acknowledge clock pulse. The slave-
receiver must pull down the SD line, during the acknowledge clock pulse, so that it remains stable LOW during the
HIGH period of the clock pulse. The CH7003 always acknowledges for writes (see
Figure 21
). Note that the
resultant state on SD is the wired-AND of data outputs from the transmitter and receiver.
Figure 21: Acknowledge on the Bus
Figure 22
shows two consecutive alternating write cycles for AutoInc = 0 and R/W = 0. The byte of information,
following the Register Address Byte (RAB), is the data to be written into the register specified by AR[5:0]. If
AutoInc = 0, then another RAB is expected from the master device, followed by another data byte, and so on.
SC from
Master
SD Data Output
By the CH7003
Start
Condition
2
SD Data Output
By Master-Transmitter
1
8
9
not acknowledge
acknowledge
clock pulse for
acknowledgement
相關PDF資料 |
PDF描述 |
|---|---|
| CH7006C | MODULE |
| CH7006C-T | Circular Connector; Body Material:Aluminum; Series:PT06; Number of Contacts:18; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-18 |
| CH7006C-V | Circular Connector; Body Material:Aluminum; Series:PT06; No. of Contacts:18; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Circular Contact Gender:Socket; Insert Arrangement:14-18 |
| CH7013A | Digital PC to TV Encoder |
| CH7013A-T | Digital PC to TV Encoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CH7004C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision |
| CH7004C-T | 制造商:CHRONTEL 功能描述: |
| CH7004C-V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision |
| CH7005C-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision |
| CH7005C-V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital PC to TV Encoder with Macrovision |
發布緊急采購，3分鐘左右您將得到回復。