- 您現在的位置：買賣IC網 > PDF目錄1908 > CPC5601D (IXYS Integrated Circuits Division)IC DRVR PROGRAMMABLE 16-SOIC PDF資料下載
參數資料
| 型號： | CPC5601D |
| 廠商： | IXYS Integrated Circuits Division |
| 文件頁數： | 13/15頁 |
| 文件大小： | 0K |
| 描述： | IC DRVR PROGRAMMABLE 16-SOIC |
| 標準包裝： | 50 |
| 系列： | CPC |
| 類型： | 驅動器 |
| 電源電壓： | 2.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
INTEGRATED CIRCUITS DIVISION
CPC5601
R04
www.ixysic.com
7
2.1 Application Circuit Configurations
Figure 4 shows LITELINK II in circuit designed to use
the optical snoop circuit in the CPC5601 for ring
detection. Figure 5 shows LITELINK III in a circuit that
uses the LITELINK snoop circuit ring detection and
display feature (caller ID) signal processing. Note that
either generation of LITELINK can be used with either
signal monitoring scheme. Using the optical path on
the CPC5601 for ring detect precludes on-hook dis-
play feature signal processing.
2.2 AC Termination
2.2.1 LITELINK II
The networks connected to outputs b1, b2, b3 and b4
provide selectable telephone line AC termination
depending on which network is switched in place of
RZNT (see the appropriate LITELINK data sheet and the
application note Understanding LITELINK for more infor-
mation).
In North American applications, turn outputs b1 and
b2 on, and turn outputs b3 and b4 off to switch in the
required 600
AC termination. For European applica-
tions, turn outputs b1 and b2 off, and outputs b3 and
b4 on to switch in the complex AC termination net-
work.
2.2.2 LITELINK III
The networks connected to outputs b1 and b3 provide
selectable telephone line AC termination depending
on which network is switched in place of RZNT (see the
appropriate LITELINK data sheet and the application
note Understanding LITELINK for more information). The
resistor connected to output b2 provides the required
bias current for North American applications.
In North American applications, turn outputs b1 and
b2 on, and turn output b3 off to switch in the required
600
AC termination. For European applications, turn
outputs b1 and b2 off, and output b3 on to switch in the
complex AC termination network.
2.3 LITELINK III Gain
Turning output 5 on adds attenuation to the receive
path, which is required for the complex termination.
Asserting the MODE pin on LITELINK III corrects for
the added attenuation.
2.4 Current Limiting
Clare recommends using the default value for RZDC
to set the loop-current limit to 133 mA. You can, if
required, adjust the current limit level by adding R73
and using output b6 to switch this value in parallel with
RZDC. See the appropriate LITELINK datasheet for
more information on setting loop-current limits.
相關PDF資料 |
PDF描述 |
|---|---|
| CPC5710N | IC PHONE LINE MONITOR 8-SOIC |
| CPC5712U | PHONE LINE MON W/DETECTOR 16QSOP |
| CPC7220W | IC ANALOG SWITCH 8CH HV 28-PLCC |
| CPC7232W | IC ANALOG SWITCH 8CH HV 28-PLCC |
| CPC7514Z | IC LINE CARD ACCESS SWITC 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPC5601DTR | 功能描述:固態繼電器-PCB安裝 Programmable Driver IC, T/R RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC5602 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:N-Channel Depletion Mode FET |
| CPC5602_12 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:N-Channel Depletion Mode FET |
| CPC5602C | 功能描述:MOSFET MOSFET N-CHANNEL 350V RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| CPC5602CTR | 功能描述:MOSFET N Channel Depletion Mode FET, T/R RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。