- 您現在的位置：買賣IC網 > PDF目錄1908 > CPC5712U (IXYS Integrated Circuits Division)PHONE LINE MON W/DETECTOR 16QSOP PDF資料下載
參數資料
| 型號： | CPC5712U |
| 廠商： | IXYS Integrated Circuits Division |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | PHONE LINE MON W/DETECTOR 16QSOP |
| 標準包裝： | 100 |
| 功能： | 電話線監控器，帶檢測器（PLMD） |
| 電路數： | 1 |
| 電源電壓： | 3 V ~ 5.5 V |
| 電流 - 電源： | 1.72mA |
| 功率（瓦特）： | 50mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOP |
| 包裝： | 管件 |
| 包括： | 固定電平極性檢測器，電平檢測器 |
INTEGRATED CIRCUITS DIVISION
CPC5712
6
www.ixysic.com
R02
In the case of the detector 2 switching points, DET2
will be low after the |TIP/RING| voltage has decreased
below a threshold set at VL2. DET2 will not transition
high until after the |TIP/RING| voltage has increased
above a threshold set at VH2. This |TIP/RING| voltage
will be larger than the threshold set at VL2. As an
example, the voltage at VL2 represents a |TIP/RING|
threshold of 20V and VH2 represents a TIP/RING
threshold of 22V. DET2 will be low if the |TIP/RING|
voltage decreases below 20V, and it will remain low
until the |TIP/RING| voltage increases above 22V.
DET2 will change states for both positive and negative
values of TIP/RING voltage as represented by
|TIP/RING|. This means that DET2 will also be low if
the TIP/RING voltage decreases below -20V and will
remain low until the TIP/RING voltage increases
beyond -22V. The user must rely on POLARITY to
determine whether the TIP/RING threshold changed
due to a positive or negative differential signal since
DET2 does not contain any polarity information.
DET1 behaves similarly to DET2, except that it is
triggered based on the voltage set at VL1 and VH1.
This means that DET1 will be low after the |TIP/RING|
voltage has decreased below the value set by the
voltage at VL1 and will not change high until after the
|TIP/RING| voltage has increased above the value set
by the voltage at VH1. DET1 does not give any polarity
information for the same reasons as defined for DET2.
In the application circuit provided, the TIP/RING
threshold levels of DET2 will always be higher than the
threshold levels of DET1.
2.5 Detector Threshold Operation
VL1, VH1, VL2, and VH2: Inputs used to set the
|TIP/RING| threshold levels that are to be detected.
VH1 and VL1 are used to set the high and low threshold
levels. The difference between VH1 and VL1 sets the
hysteresis for the 1st threshold level. VH2 and VL2 are
used to set the threshold and hysteresis for the 2nd
threshold level. There is a digital output for both the 1st
and 2nd threshold levels that shows when the
|TIP/RING| voltage has crossed a threshold level and
when it has exceeded the configured hysteresis level.
This was explained in the DET1 and DET2 definitions.
In general, the digital output will be low when the
|TIP/RING| voltage has fallen below the VL# level and
will change high again once the |TIP/RING| voltage
has risen above the VH# level.
VREF: An analog output that is similar to the DC bias
level that is applied to OUT+ and OUT-. This voltage is
brought off chip so that it can be used to define
threshold detection levels. Load capacitance on this
pin must be kept less than the value recommended in
the table Recommended Operating Conditions.
The total load resistance on this pin must be within the
range specified in the table Recommended
Resistors R1, R2, R3, R4 and R5 are external
resistors, which must be provided by the user. The
selection of the resistors determines the voltages at
VL2, VH2, VL1 and VH1 and therefore the threshold and
hysteresis values for the 2 detectors.
The values for R1, R2, R3, R4, and R5 are easily
determined. Select voltage levels for the 1st and 2nd
threshold and hysteresis settings such that:
VH2 > VL2 > VH1 > VL1
Then use the following algorithm to find the values of
R2, R3, R4 and R5.
1.
Select a value for R1.
2.
R2 = (R1(VH1-VL1)) / VL1
3.
R3 = (R1(VL2-VH1))/ VL1
4.
R4 = (R1(VH2-VL2)) / VL1
5.
R5 = (R1(VREF/A-VH2)) / VL1
V
REF = 1.5V
A = (2.5 (R
DIFF)) / (RIN1 + RIN2 + RDIFF), which
typically calculates to 0.05; in this case: 0.04938.
See Figure 1.
Also, as shown in the table of Recommended
Operating Conditions, the resistive load on the VREF
pin must fall within the range:
20k
< (R1 + R2 + R3 + R4 + R5) < 1M
2.6 Power Connections
VCC, Ground: Power supply pins. These are used to
supply voltage and ground to the chip.
相關PDF資料 |
PDF描述 |
|---|---|
| CPC7220W | IC ANALOG SWITCH 8CH HV 28-PLCC |
| CPC7232W | IC ANALOG SWITCH 8CH HV 28-PLCC |
| CPC7514Z | IC LINE CARD ACCESS SWITC 20SOIC |
| CS4121ENF16G | IC TACH/SPEEDO DRIVER 16-DIP |
| CS4122XDWF24G | IC DRIVER AIR CORE TRPL 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPC5712UTR | 功能描述:固態繼電器-PCB安裝 Phone Line Monitor,T/R RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC5750U | 功能描述:Telecom IC CODEC 24-SSOP 制造商:ixys integrated circuits division 系列:- 包裝:管件 零件狀態:有效 功能:CODEC 接口:SPI 電路數:1 電壓 - 電源:3 V ~ 3.6 V 電流 - 電源:7.5mA 功率（W）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-SSOP（0.154"，3.90mm 寬） 供應商器件封裝:24-SSOP 包括:- 標準包裝:50 |
| CPC5750UTR | 功能描述:IC VOICE BAND CODEC 24SSOP 制造商:ixys integrated circuits division 系列:- 包裝:帶卷（TR） 零件狀態:在售 功能:CODEC 接口:SPI 電路數:1 電壓 - 電源:3 V ~ 3.6 V 電流 - 電源:7.5mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-SSOP（0.154"，3.90mm 寬） 供應商器件封裝:24-SSOP 包括:- 標準包裝:2,000 |
| CPC5902G | 功能描述:ISOLAT 3.75KVRMS 2CH BIDIR 8DIP RoHS:是 類別:隔離器 >> 光隔離器 - 邏輯輸出 系列:- 標準包裝:1,000 系列:- 電壓 - 隔離:3750Vrms 通道數:1，單向 電流 - 輸出 / 通道:50mA 數據速率:15MBd 傳輸延遲高 - 低 @ 如果:50ns @ 7.5mA 電流 - DC 正向(If):20mA 輸入類型:DC 輸出類型:開路集電極 安裝類型:表面貼裝 封裝/外殼:8-SMD，鷗翼型 供應商設備封裝:8-DIP 鷗翼型 包裝:帶卷 (TR) |
| CPC5902G_5903G-EVAL | 功能描述:CPC5902, CPC5903 - Interface, Buffer/Repeater Evaluation Board 制造商:ixys integrated circuits division 系列:- 零件狀態:有效 主要用途:接口，緩沖器/中繼器 嵌入式:- 使用的 IC/零件:CPC5902，CPC5903 主要屬性:隔離 輔助屬性:- 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。