- 您現在的位置：買賣IC網 > PDF目錄378470 > CXD1196 (Sony Corporation) CD-ROM DECODER PDF資料下載
參數資料
| 型號： | CXD1196 |
| 廠商： | Sony Corporation |
| 英文描述： | CD-ROM DECODER |
| 中文描述： | CD - ROM譯碼 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 278K |
| 代理商： | CXD1196 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
—17—
CXD1196AR
2. Register Functions
2.1 Write register
2.1.1
Register address (REGADR) register
This register is used for selection of the internal registers.
(1) When A0 = XCS = ‘L’, the REGADR register is selected. When A0 = ‘H’ and XCS = ‘L’, the register
specified by the REGADR is selected.
(2) When the low order 4 bits of REGADR are not 0 (hex), and a register write or read is made by setting
A0 = ‘H’ and XCS = ‘L’, the low order 4 bits of REGADR are incremented.
(3) REGADR is cleared by rising edge of DMAEN bit (bit3) of the DMACTL register. (Cleared to 00 (hex).)
2.1.2
DRIVE Interface (DRVIF) register
XSLOW (/SLOW SPEED)
‘H’
:
A DMA cycle is performed in 4 clocks.
In this case, a standard SRAM with an access time of less than 120 nsec can be connected
to the CXD1196AR.
‘L’
:
A DMA cycle is performed in 12 clocks. When the CXD1196R is connected to an SRAM
with a slower access time, set this bit at ‘L’. In this case, a standard SRAM with an access
time of less than 320 ns can be connected to the CXD1196AR. For operation at V
DD
= 3.5
V, set this bit to L.
Bit6 C2PL1ST (C2PO Ler-byte 1st)
‘H’
:
To input two bytes of DATA input, each with a C2PO identifying the lower or upper byte, in
the order of the lower and upper bytes
‘L’
:
To input two bytes of DATA input, each with a C2PO identifying the upper or lower byte, in
the order of the upper and lower bytes.
Here, the upper byte means the 8 (eight) upper bits including the MSB from the DSP for CD. And the lower
byte means the 8 (eight) lower bits including the LSB from the DSP for CD. For example, the minute byte
of the Header is a lower byte and the sec byte is a upper byte.
Bit7
Bit5
LCHLOW (LCH LOW)
‘H’
:
To determine that the data is Lch data when LRCK = ‘L’
‘L’
:
To determine that the data is Lch data when LRCK = ‘H’
Bit4
BCKRED (BCLK Rising Edge)
‘H’
:
To strobe DATA by the rising edge of BCLK
‘L’
:
To strobe DATA by the falling edge of BCLK
Bit3, 2 BCKMD1, 0 (BCLK Mode 1, 0)
Set these bits, depending on the number of BCLK clocks output by the DSP for CD during a cycle of
WCLK.
Bit1
LSB 1ST (LSB First)
‘H’
:
To connect to a DSP for CD which outputs DATA on an LSB first basis
‘L’
:
To connect to a DSP for CD which outputs DATA on an MSB first basis
Bit0
CLKLOW (CLK LOW)
‘H’
:
To fix CLK pin output at ‘L’
‘L’
:
To output 8.4672 MHz clock from CLK pin output
The values of the individual bits of this register must be changed with the decoder in the disabled state.
Table 2.1.1 shows the values of bits of bit 6 through 1 to be set when the CXD1196AR is connected to
Sony DSPs for CD. Fig. 2.2.1 (1) through (3) show input timing charts.
BCKMD1
‘L’
‘L’
‘H’
BCKMD0
‘L’
‘H’
‘X’
16BCLKs/WCLK
24BCLKs/WCLK
32BCLKs/WCLK
相關PDF資料 |
PDF描述 |
|---|---|
| CXD1196AR | CD-ROM DECODER |
| CXD1198AQ | CD-ROM Subcode Decoder |
| CXD1199AQ | CD-ROM DECODER |
| CXD1257AR | CCD Camera Timing Generator |
| CXD1267AN | CCD Vertical Clock Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CXD1196AR | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD-ROM DECODER |
| CXD1197AQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CD-ROM Interface |
| CXD1198AQ | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD-ROM Subcode Decoder |
| CXD1199AQ | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD-ROM DECODER |
| CXD12-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。