![](http://datasheet.mmic.net.cn/160000/CY39030Z144-222BBC_datasheet_8625318/CY39030Z144-222BBC_16.png)
PRELIMINARY
Delta39K ISR
CPLD Family
Document #: 38-03039 Rev. **
Page 16 of 57
Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature .................................. –65
°C to +150°C
Soldering Temperature...................................................220
°C
Ambient Temperature with
Power Applied............................................... –40
°C to +85°C
Junction Temperature....................................................135
°C
VCC to Ground Potential (39KZ device)......... .. –0.5V to 2.5V
VCC to Ground Potential (39KV device) ...........–0.5V to 4.6V
VCCIO to Ground Potential................................–0.5V to 4.6V
DC Voltage Applied to Outputs in High Z State –0.5V to 4.5V
DC Input voltage......................... ......................–0.5V to 4.5V
DC Current into Outputs........................ .................................
[6]
Static Discharge Voltage (per MIL-STD-8883,
Method 3015)..............................................................>2001V
Latch-Up Current.......................................................>200 mA
Notes:
6.
DC current into outputs is 36 mA with HSTL III, 48 mA with HSTL IV and 36 mA with GTL+ (with 25
pull-up resistor and V
TT = 1.5
7.
Not more than one output should be tested at a time. Duration of the short circuit should not exceed 1 second. VOUT = 0.5V has been chosen to avoid test
problems caused by tester ground degradation. Tested initially and after any design or process changes that may affect these parameters.
Operating Range
Range
Ambient
Temperature
Junction
Temperature
Output
Condition
VCCIO
VCC
VCCJTAG/
VCCCNFG VCCPLL VCCPRG
Commercial
0
°C to +70°C
0
°C to +85°C
3.3V
3.3V ± 0.3V
or
2.5V ± 0.2V
(39KV)
1.8V ± 0.15V
(39KZ)
Same as
VCCIO
Same
as VCC
3.3V
±
0.3V
2.5V
2.5V ± 0.2V
1.8V
1.8V ± 0.15V
1.5V
1.5V ± 0.1V[5]
Industrial
–40
°C to +85°C –40°C to +100°C
3.3V
3.3V ± 0.3V
2.5V
2.5V ± 0.2V
1.8V
1.8V ± 0.15V
1.5V
1.5V ± 0.1V[5]
DC Characteristics
Parameter Description
Test Conditions
VCCIO = 3.3 V VCCIO = 2.5 V VCCIO = 1.8 V
Unit
Min.
Max.
Min.
Max.
Min.
Max.
VDRINT
Data Retention VCC Voltage
(config data may be lost below this)
1.5
V
VDRIO
Data Retention VCCIO Voltage
(config data may be lost below this)
1.2
V
IIX
Input Leakage Current
GND
≤ V
I ≤ 3.6V
–10
10
–10
10
–10
10
A
IOZ
Output Leakage Current
GND
≤ V
O ≤ VCCIO
–10
10
–10
10
–10
10
A
IOS
[7]
Output Short Circuit Current
VCCIO = Max.,
VOUT = 0.5V
–160
mA
IBHL
Input Bus Hold LOW Sustaining
Current
VCC = Min.,
VPIN = VIL
+40
+30
+25
A
IBHH
Input Bus Hold HIGH Sustaining
Current
VCC = Min.,
VPIN = VIH
–40
–30
–25
A
IBHLO
Input Bus Hold LOW Overdrive Current VCC = Max.
+250
+200
+150
A
IBHHO
Input Bus Hold HIGH Overdrive Current VCC = Max.
–250
–200
–150
A