- 您現在的位置：買賣IC網 > PDF目錄378516 > CYP15G0401DXB-BGI (CYPRESS SEMICONDUCTOR CORP) Quad HOTLink II Transceiver PDF資料下載
參數資料
| 型號： | CYP15G0401DXB-BGI |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Quad HOTLink II Transceiver |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | BGA-256 |
| 文件頁數： | 40/48頁 |
| 文件大小： | 1115K |
| 代理商： | CYP15G0401DXB-BGI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
CYP15G0401DXA
PRELIMINARY
Document #: 38-02002 Rev. *B
Page 40 of 48
X3.230 Codes and Notation Conventions
Information to be transmitted over a serial link is encoded eight
bits at a time into a 10-bit Transmission Character and then
sent serially, bit by bit. Information received over a serial link is
collected ten bits at a time, and those Transmission Characters
that are used for data (Data Characters) are decoded into the
correct eight-bit codes. The 10-bit Transmission Code sup-
ports all 256 8-bit combinations. Some of the remaining Trans-
mission Characters (Special Characters) are used for func-
tions other than data transmission.
The primary rationale for use of a Transmission Code is to
improve the transmission characteristics of a serial link. The
encoding defined by the Transmission Code ensures that suf-
ficient transitions are present in the serial bit stream to make
clock recovery possible at the Receiver. Such encoding also
greatly increases the likelihood of detecting any single or mul-
tiple bit errors that may occur during transmission and recep-
tion of information. In addition, some Special Characters of the
Transmission Code selected by Fibre Channel Standard con-
sist of a distinct and easily recognizable bit pattern (the Special
Character COMMA) that assists a Receiver in achieving word
alignment on the incoming bit stream.
Notation Conventions
The documentation for the 8B/10B Transmission Code uses
letter notation for the bits in an 8-bit byte. Fibre Channel Stan-
dard notation uses a bit notation of A, B, C, D, E, F, G, H for
the 8-bit byte for the raw 8-bit data, and the letters a, b, c, d, e,
i, f, g, h, j for encoded 10-bit data. There is a correspondence
between bit A and bit a, B and b, C and c, D and d, E and e, F
and f, G and g, and H and h. Bits i and j are derived, respec-
tively, from (A,B,C,D,E) and (F,G,H).
The bit labeled A in the description of the 8B/10B Transmission
Code corresponds to bit 0 in the numbering scheme of the FC-
2 specification, B corresponds to bit 1, as shown below.
FC-2 bit designation
—
HOTLink D/Q designation
—
7
8B/10B bit designation
—
To clarify this correspondence, the following example shows
the conversion from an FC-2 Valid Data Byte to a Transmission
Character (using 8B/10B Transmission Code notation)
FC-2
45
Bits: 7654 3210
7
6
6
5
5
4
4
E
3
3
D C B
2
2
1
1
0
0
A
H G F
0100 0101
Converted to 8B/10B notation (note carefully that the order of
bits is reversed):
Data Byte Name
D5.2
Bits:ABCDEFGH
10100 010
Translated to a transmission Character in the 8B/10B Trans-
mission Code:
Bits: abcdeifghj
1010010101
Each valid Transmission Character of the 8B/10B Transmis-
sion Code has been given a name using the following conven-
tion: cxx.y, where c is used to show whether the Transmission
Character is a Data Character (c is set to D, and SC/D = LOW)
or a Special Character (c is set to K, and SC/D = HIGH). When c is
set to D, xx is the decimal value of the binary number composed of
the bits E, D, C, B, and A in that order, and the y is the decimal value
of the binary number composed of the bits H, G, and F in that order.
When c is set to K, xx and y are derived by comparing the encoded
bit patterns of the Special Character to those patterns derived from
encoded Valid Data bytes and selecting the names of the patterns
most similar to the encoded bit patterns of the Special Character.
Under the above conventions, the Transmission Character
used for the examples above, is referred to by the name D5.2.
The Special Character K29.7 is so named because the first six
bits (abcdei) of this character make up a bit pattern similar to
that resulting from the encoding of the unencoded 11101 pat-
tern (29), and because the second four bits (fghj) make up a
bit pattern similar to that resulting from the encoding of the
unencoded 111 pattern (7).
Note:
This definition of the 10-bit Transmission Code is based
on (and is in basic agreement with) the following references,
which describe the same 10-bit transmission code.
A.X. Widmer and P.A. Franaszek.
“
A DC-Balanced, Parti-
tioned-Block, 8B/10B Transmission Code
”
IBM Journal of Re-
search and Development
, 27, No. 5: 440
451 (September, 1983).
U.S. Patent 4,486,739. Peter A. Franaszek and Albert X. Wid-
mer.
“
Byte-Oriented DC Balanced (0.4) 8B/10B Partitioned
Block Transmission Code
”
(December 4, 1984).
Fibre Channel Physical and Signaling Interface (ANS X3.230
1994 ANSI FC
PH Standard).
IBM Enterprise Systems Architecture/390 ESCON I/O Inter-
face (document number SA22
7202).
8B/10B Transmission Code
The following information describes how the tables shall be
used for both generating valid Transmission Characters (en-
coding) and checking the validity of received Transmission
Characters (decoding). It also specifies the ordering rules to
be followed when transmitting the bits within a character and
the characters within the higher-level constructs specified by
the standard.
Transmission Order
Within the definition of the 8B/10B Transmission Code, the bit
positions of the Transmission Characters are labeled a, b, c, d,
e, i, f, g, h, j. Bit
“
a
”
shall be transmitted first followed by bits b,
c, d, e, i, f, g, h, and j in that order. (Note that bit i shall be
transmitted between bit e and bit f, rather than in alphabetical
order.)
Valid and Invalid Transmission Characters
The following tables define the valid Data Characters and valid
Special Characters (K characters), respectively. The tables are
used for both generating valid Transmission Characters (en-
coding) and checking the validity of received Transmission
Characters (decoding). In the tables, each Valid-Data-byte or
Special-Character-code entry has two columns that represent
two (not necessarily different) Transmission Characters. The
two columns correspond to the current value of the running
disparity (
“
Current RD
”
or
“
Current RD+
”
). Running disparity
is a binary parameter with either the value negative (
) or the
value positive (+).
After powering on, the Transmitter may assume either a posi-
tive or negative value for its initial running disparity. Upon
transmission of any Transmission Character, the transmitter
will select the proper version of the Transmission Character
相關PDF資料 |
PDF描述 |
|---|---|
| CYP15G0401DXA-BGC | Quad HOTLink II Transceiver |
| CYP15G0401DXA-BGI | Quad HOTLink II Transceiver |
| CYRF6936 | WirelessUSB LP 2.4GHz Radio SoC(WirelessUSB LP 2.4GHz無線SoC) |
| CYV15G0104TRB | Independent Clock HOTLink II Serializer and Reclocking Deserializer(獨立時鐘，HOTLink II并串轉換器及時鐘恢復串并轉換器) |
| CYV15G0201DXB-BBI | Dual-channel HOTLink II Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYP15G0401DXB-BGXC | 功能描述:電信線路管理 IC Dual Channel XCVR 1.5Gbps Bckplane COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYP15G0401DXB-BGXCKG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cypress Semiconductor 功能描述: |
| CYP15G0401DXBBGXI | 制造商:Cypress Semiconductor 功能描述: |
| CYP15G0401DXB-BGXI | 功能描述:電信線路管理 IC Quad HOTLink II XCVR Ch 1.5Gbps Backplane RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYP15G0401DX-BGC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。