- 您現在的位置：買賣IC網 > PDF目錄376564 > DAC8532IDGK Dual Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER PDF資料下載
參數資料
| 型號： | DAC8532IDGK |
| 英文描述： | Dual Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER |
| 中文描述： | 雙通道，低功耗，16位，串行輸入數字到模擬轉換器 |
| 文件頁數： | 14/19頁 |
| 文件大?。?/td> | 402K |
| 代理商： | DAC8532IDGK |
DAC8532
SBAS246A
14
www.ti.com
DAC8532 to Microwire INTERFACE
Figure 7 shows an interface between the DAC8532 and any
Microwire compatible device. Serial data is shifted out on the
falling edge of the serial clock and is clocked into the
DAC8532 on the rising edge of the SK signal.
MICROPROCESSOR
INTERFACING
DAC8532 to 8051 INTERFACE
Figure 6 shows a serial interface between the DAC8532 and
a typical 8051-type microcontroller. The setup for the inter-
face is as follows: TXD of the 8051 drives SCLK of the
DAC8532, while RXD drives the serial data line of the device.
The SYNC signal is derived from a bit-programmable pin on
the port of the 8051. In this case, port line P3.3 is used. When
data is to be transmitted to the DAC8532, P3.3 is taken LOW.
The 8051 transmits data in 8-bit bytes; thus only eight falling
clock edges occur in the transmit cycle. To load data to the
DAC, P3.3 is left LOW after the first eight bits are transmitted,
then a second and third write cycle is initiated to transmit the
remaining data. P3.3 is taken HIGH following the completion
of the third write cycle. The 8051 outputs the serial data in a
format which presents the LSB first, while the DAC8532
requires its data with the MSB as the first bit received. The
8051 transmit routine must therefore take this into account,
and
“
mirror
”
the data as needed.
The 68HC11 should be configured so that its CPOL bit is 0
and its CPHA bit is 1. This configuration causes data appear-
ing on the MOSI output to be valid on the falling edge of SCK.
When data is being transmitted to the DAC, the SYNC line is
held LOW (PC7). Serial data from the 68HC11 is transmitted
in 8-bit bytes with only eight falling clock edges occurring in
the transmit cycle. (Data is transmitted MSB first.) In order to
load data to the DAC8532, PC7 is left LOW after the first
eight bits are transferred, then a second and third serial write
operation is performed to the DAC. PC7 is taken HIGH at the
end of this procedure.
DAC8532 to TMS320 DSP INTERFACE
Figure 9 shows the connections between the DAC8532 and
a TMS320 digital signal processor. By decoding the FSX
signal, multiple DAC8532s can be connected to a single
serial port of the DSP.
FIGURE 6. DAC8532 to 80C51/80L51 Interface.
FIGURE 7. DAC8532 to Microwire Interface.
FIGURE 8. DAC8532 to 68HC11 Interface.
DAC8532 to 68HC11 INTERFACE
Figure 8 shows a serial interface between the DAC8532 and
the 68HC11 microcontroller. SCK of the 68HC11 drives the
SCLK of the DAC8532, while the MOSI output drives the
serial data line of the DAC. The SYNC signal is derived from
a port line (PC7), similar to the 8051 diagram.
FIGURE 9. DAC8532 to TMS320 DSP.
APPLICATIONS
CURRENT CONSUMPTION
The DAC8532 typically consumes 250uA at V
DD
= 5V and
225uA at V
DD
= 3V for each active channel, including refer-
ence current consumption. Additional current consumption
can occur at the digital inputs if V
IH
<<V
DD
. For most efficient
power operation, CMOS logic levels are recommended at the
digital inputs to the DAC.
In power-down mode, typical current consumption is 200nA.
A delay time of 10 to 20ms after a power-down command is
issued to the DAC is typically sufficient for the power-down
current to drop below 10
μ
A.
DAC8532
TMS320 DSP
SYNC
D
IN
SCLK
FSX
DX
CLKX
V
DD
V
OUT
A
V
OUT
B
Output A
Output B
Reference
Input
V
REF
GND
0.1
μ
F
1
μ
F to 10
μ
F
Positive Supply
0.1
μ
F
10
μ
F
80C51/80L51
(1)
P3.3
TXD
RXD
DAC8532
(1)
SYNC
SCLK
D
IN
NOTE: (1) Additional pins omitted for clarity.
SYNC
SCLK
D
IN
Microwire
TM
CS
SK
SO
DAC8532
(1)
NOTE: (1) Additional pins omitted for clarity.
Microwire is a registered trademark of National Semiconductor.
68HC11
(1)
PC7
SCK
MOSI
SYNC
SCLK
D
IN
DAC8532
(1)
NOTE: (1) Additional pins omitted for clarity.
相關PDF資料 |
PDF描述 |
|---|---|
| DAC8541EVM | DAC8541EVM(DAC8541評估板) |
| DAC8544I | QUAD, 16-BIT, RAIL-TO-RAIL VOLTAGE OUTPUT, PARALLEL INTERFACE, DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDGK | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDRBR | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
| DAC8551IDRBT | 16-BIT, ULTRA-LOW GLITCH, VOLTAGE OUTPUT DIGITAL-TO-ANALOG CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC8532IDGK | 制造商:Texas Instruments 功能描述:16BIT DUAL DAC SMD 8532 MSOP8 |
| DAC8532IDGKG4 | 功能描述:數模轉換器- DAC 16-Bit Dual Ch Low Power DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8532IDGKR | 功能描述:數模轉換器- DAC 16-Bit Dual Ch Low Power DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8532IDGKRG4 | 功能描述:數模轉換器- DAC 16-Bit Dual Ch Low Power DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC8534 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Quad Channel, Low Power, 16-Bit, Serial Input DIGITAL-TO-ANALOG CONVERTER |
發布緊急采購，3分鐘左右您將得到回復。