- 您現在的位置：買賣IC網 > PDF目錄295418 > DAC908E/2K5 PARALLEL, 8 BITS INPUT LOADING, 0.03 us SETTLING TIME, 8-BIT DAC, PDSO28 PDF資料下載
參數資料
| 型號： | DAC908E/2K5 |
| 元件分類： | DAC |
| 英文描述： | PARALLEL, 8 BITS INPUT LOADING, 0.03 us SETTLING TIME, 8-BIT DAC, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 7/15頁 |
| 文件大小： | 180K |
| 代理商： | DAC908E/2K5 |
DAC908
15
Further supply decoupling with surface mount tantalum
capacitors (1uF to 4.7uF) may be added as needed in
proximity of the converter.
Low noise is required for all supply and ground connections
to the DAC908. It is recommended to use a multilayer pc-
board utilizing separate power and ground planes. Mixed
signal designs require particular attention to the routing of
the different supply currents and signal traces. Generally,
analog supply and ground planes should only extend into
analog signal areas, such as the DAC output signal and the
reference signal. Digital supply and ground planes must be
confined to areas covering digital circuitry, including the
digital input lines connecting to the converter, as well as the
clock signal. The analog and digital ground planes should be
joined together at one point underneath the D/A converter.
This can be realized with a short track of approximately
1/8inch (3mm).
The power to the DAC908 should be provided through the
use of wide pcb runs or planes. Wide runs will present a
lower trace impedance, further optimizing the supply decou-
pling. The analog and digital supplies for the converter
should only be connected together at the supply connector of
the pc board. In the case of only one supply voltage being
available to power the DAC, ferrite beads along with bypass
capacitors may be used to create an LC filter. This will
generate a low noise analog supply voltage, which can then
be connected to the +V
A supply pin of the DAC908.
While designing the layout, it is important to keep the analog
signal traces separated from any digital line, in order to
prevent noise coupling onto the analog signal path.
相關PDF資料 |
PDF描述 |
|---|---|
| DAC908U/1K | PARALLEL, 8 BITS INPUT LOADING, 0.03 us SETTLING TIME, 8-BIT DAC, PDSO28 |
| DAC908U | PARALLEL, 8 BITS INPUT LOADING, 0.03 us SETTLING TIME, 8-BIT DAC, PDSO28 |
| DAT-3175-PN | 0 MHz - 2000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 2.1 dB INSERTION LOSS-MAX |
| DA | FEMALE; MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| DB0440LW1H | 4000 MHz - 40000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 11 dB CONVERSION LOSS-MAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DAC908EG4 | 功能描述:數模轉換器- DAC 8-Bit 165MSPS SpeedPlus DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC908U | 功能描述:數模轉換器- DAC 8-Bit 165MSPS SpeedPlus DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC908U | 制造商:Texas Instruments 功能描述:8 BIT DIGITAL/ANALOG CONVERTER 8 RESOLU |
| DAC908U/1K | 功能描述:數模轉換器- DAC 8-Bit 165MSPS SpeedPlus DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DAC908U/1KG4 | 功能描述:數模轉換器- DAC 8-Bit 165MSPS SpeedPlus DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。