I2C INTERFACE The LTC2495 communicates through " />
參數資料
型號： DC1012A-C
廠商： Linear Technology
文件頁數： 7/34頁
文件大?。?/td> 0K
描述： BOARD DELTA SIGMA ADC LTC2495
軟件下載： QuikEval System
設計資源： DC1012A Schematic
DC1012A Design File
標準包裝： 1
系列： Easy Drive™, QuikEval™
ADC 的數量： 1
位數： 16
采樣率（每秒）： 15
數據接口： I²C，串行
已用 IC / 零件： LTC2495
已供物品： 板
相關產品： LTC2495IUHF#TRPBF-ND - IC ADC 16BIT W/PGA 38-QFN
LTC2495CUHF#TRPBF-ND - IC ADC 16BIT W/PGA 38-QFN
LTC2495CUHF#PBF-ND - IC ADC 16BIT W/PGA 38-QFN
LTC2495IUHF#PBF-ND - IC ADC 16BIT W/PGA 38-QFN
LTC2495
2495fd
I2C INTERFACE
The LTC2495 communicates through an I2C interface. The
I2C interface is a 2-wire, open-drain interface supporting
multiple devices and multiple masters on a single bus. The
connected devices can only pull the data line (SDA) LOW
and can never drive it HIGH. SDA is required to be exter-
nally connected to the supply through a pull-up resistor.
When the data line is not being driven, it is HIGH. Data on
the I2C bus can be transferred at rates up to 100kbits/s in
the standard mode and up to 400kbits/s in the fast mode.
The VCC power should not be removed from the device
when the I2C bus is active to avoid loading the I2C bus
lines through the internal ESD protection diodes.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate either as a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
canalsobeconsideredasmastersorslaveswhenperform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. Devices addressed by the master
are considered a slave.
The LTC2495 can only be addressed as a slave. Once
addressed, it can receive configuration bits (channel
selection, rejection mode, speed mode) or transmit the
last conversion result. The serial clock line, SCL, is always
an input to the LTC2495 and the serial data line SDA is
bidirectional. The device supports the standard mode and
the fast mode for data transfer speeds up to 400kbits/s.
Figure 2 shows the definition of the I2C timing.
The START and STOP Conditions
A START (S) condition is generated by transitioning SDA
from HIGH to LOW while SCL is HIGH. The bus is consid-
ered to be busy after the START condition. When the data
transfer is finished, a STOP (P) condition is generated by
transitioning SDA from LOW to HIGH while SCL is HIGH.
The bus is free after a STOP is generated. START and STOP
conditions are always generated by the master.
When the bus is in use, it stays busy if a repeated START
(Sr)isgeneratedinsteadofaSTOPcondition.Therepeated
START timing is functionally identical to the START and is
used for writing and reading from the device before the
initiation of a new conversion.
Data Transferring
After the START condition, the I2C bus is busy and data
transfer can begin between the master and the addressed
slave. Data is transferred over the bus in groups of nine
bits, one byte followed by one acknowledge (ACK) bit. The
master releases the SDA line during the ninth SCL clock
cycle. The slave device can issue an ACK by pulling SDA
LOW or issue a Not Acknowledge (NACK) by leaving the
SDA line high impedance (the external pull-up resistor will
hold the line HIGH). Change of data only occurs while the
clock line (SCL) is LOW.
Figure 2. Definition of Timing for Fast/Standard Mode Devices on the I2C Bus
applications inForMation
SDA
SCL
S
Sr
P
S
tHD(SDA)
tHD(DAT)
tSU(STA)
tSU(STO)
tSU(DAT)
tLOW
tHD(SDA)
tSP
tBUF
tr
tf
tr
tf
tHIGH
2495 F02
相關PDF資料
PDF描述
SDR0604-3R3ML INDUCTOR POWER 3.3UH 20% SMD
SDR0604-151KL INDUCTOR POWER 150UH 0.40A SMD
AP2142MPG-13 IC PWR SW USB 2CH 0.5A 8-MSOP
AD9778A-DPG2-EBZ BOARD EVALUATION FOR AD9778A
SDR0403-101KL INDUCTOR 100UH 10% NON-SHLD SMD
相關代理商/技術參數
參數描述
DC-101-86-UL 制造商:Pan Pacific 功能描述:
DC1018B-A 功能描述:DEMO BOARD FOR LT4356-1 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
DC1018B-B 功能描述:DEMO BOARD FOR LT4356-2 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
DC1018B-C 功能描述:DEMO BOARD FOR LT4356-3 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
DC101-BB-B 制造商:Carling Technologies 功能描述:D-SERIES TOGGLE SWITCH - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*