- 您現在的位置：買賣IC網 > PDF目錄17063 > DC955A (Linear Technology)BOARD DELTA SIGMA ADC LTC2483 PDF資料下載
參數資料
| 型號： | DC955A |
| 廠商： | Linear Technology |
| 文件頁數： | 3/34頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2483 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC955A Design File DC955A Schematic |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | I²C，串行 |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2483 |
| 已供物品： | 板 |
| 相關產品： | LTC2483IDD#TRPBF-ND - IC ADC 16BIT I2C 10-DFN LTC2483CDD#TRPBF-ND - IC ADC 16BIT I2C 10-DFN LTC2483IDD#PBF-ND - IC ADC 16BIT I2C 10-DFN LTC2483CDD#PBF-ND - IC ADC 16BIT I2C 10-DFN |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LTC2483
2483fc
CONVERTER OPERATION
Converter Operation Cycle
The LTC2483 is a low power, ∑ analog-to-digital con-
verter with an I2C interface. After power-on reset, its
operation is made up of three states. The converter
operating cycle begins with the conversion, followed by
the low power sleep state and ends with the data output
(see Figure 1).
applicaTions inFormaTion
Figure 1. LTC2483 State Transition Diagram
CONVERSION
POWER-ON RESET
SLEEP
2483 F01
YES
NO
ACKNOWLEDGE
YES
NO
STOP
OR READ
24 BITS
DATA OUTPUT
Initially, the LTC2483 performs a conversion. Once the
conversion is complete, the device enters the sleep state.
While in this sleep state, power consumption is reduced
by two orders of magnitude. The part remains in the sleep
state as long as it is not addressed for a read operation.
The conversion result is held indefinitely in a static shift
register while the converter is in the sleep state.
Thedevicewillnotacknowledgeanexternalrequestduring
the conversion state. After a conversion is finished, the
device is ready to accept a read request. Once the LTC2483
is addressed for a read operation, the device begins out-
putting the conversion result under control of the serial
clock (SCL). There is no latency in the conversion result.
The data output is 24 bits long and contains a 16-bit plus
sign conversion result. This result is shifted out on the
SDA pin under the control of the SCL. Data is updated
on the falling edges of SCL allowing the user to reliably
latch data on the rising edge of SCL. A new conversion is
initiated at the conclusion of a data read operation (read
out all 24 bits).
I2C INTERFACE
The LTC2483 communicates through an I2C interface.
The I2C interface is a 2-wire open-drain interface sup-
porting multiple devices and masters on a single bus.
The connected devices can only pull the bus wires LOW
and they never drive the bus HIGH. The bus wires are
externally connected to a positive supply voltage via a
current-source or pull-up resistor. When the bus is free,
both lines are HIGH. Data on the I2C bus can be transferred
at rates of up to 100kbit/s in the standard mode and up
to 400kbit/s in the fast mode. The VCC power should not
be removed from the device when the I2C bus is active to
avoid loading the I2C bus lines through the internal ESD
protection devices.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate as either a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
canalsobeconsideredasmastersorslaveswhenperform-
ing data transfers. A master is the device which initiates a
data transfer on the bus and generates the clock signals
to permit that transfer. At the same time any device ad-
dressed is considered a slave.
The LTC2483 can only be addressed as a slave. Once
addressed, it can transmit the last conversion result.
Therefore the serial clock line SCL is an input only and
the data line SDA is bidirectional (data out/address in).
The device supports the standard mode and the fast mode
for data transfer speeds up to 400kbit/s. Figure 2 shows
the definition of timing for fast/standard mode devices
on the I2C bus.
相關PDF資料 |
PDF描述 |
|---|---|
| SDR0604-181KL | INDUCTOR POWER 180UH 0.38A SMD |
| AP2186SG-13 | IC USB PWR SWITCH 1.5A DUAL 8SOP |
| AD9755-EB | BOARD EVAL FOR AD9755 |
| HBM11DRYI-S13 | CONN EDGECARD 22POS .156 EXTEND |
| ECM25DCSH | CONN EDGECARD 50POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC956A | 功能描述:BOARD DELTA SIGMA ADC LTC2485 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:Easy Drive™, QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC959A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4257-1 制造商:Linear Technology 功能描述:EVAL BOARD, LTC4257CDD-1 POE |
| DC95F103V | 功能描述:熱敏電阻 - NTC 10KOhms +-.1C Epoxy Coated RoHS:否 制造商:EPCOS 電阻:10 kOhms 功率額定值:150 mW 容差:2 % 端接類型:Radial 系列:B57703M 工作溫度范圍:- 55 C to + 125 C |
| DC95F103VN | 制造商:GE Sensing & Inspection Technologies 功能描述:Thermistor;10;PCB Mount Mtg. Type;1.5In Lead;Bare Tinned Copper 制造商:GE Measurement & Control 功能描述:+/-.1oC (0oC - 70oC) Interchangeable Chip |
| DC95F103W | 功能描述:熱敏電阻 - NTC 10KOhms +-.2C Epoxy Coated RoHS:否 制造商:EPCOS 電阻:10 kOhms 功率額定值:150 mW 容差:2 % 端接類型:Radial 系列:B57703M 工作溫度范圍:- 55 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。