- 您現在的位置：買賣IC網 > PDF目錄1912 > DLP-245PL-G (DLP Design Inc)MOD USB-MCU FT245RL W/18LF8722 PDF資料下載
參數資料
| 型號： | DLP-245PL-G |
| 廠商： | DLP Design Inc |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | MOD USB-MCU FT245RL W/18LF8722 |
| 產品目錄繪圖： | DLP-245PL-G |
| 標準包裝： | 1 |
| 系列： | USB |
| 模塊/板類型： | 開發板 |
| 適用于相關產品： | USB |
| 其它名稱： | 813-1005 |
7
TOKEN I/O COMMAND SET
0xA5 – Line In – Reads the state of a single port pin
Parameters:
Port – Select from available port pins (PIN_A3, PIN_B0, etc.)
Returns:
1 Byte: State of the port pin (0 or 1)
Function:
This function will read the state of a single port pin. If the data direction for the
pin selected was set to output, the direction is first set to input.
Example:
0x2, 0xA5, 0x2F, 0x88 - Reads the current state of port pin PIN_A3.
0xA6 – Line Out - Sets a single port pin high or low
Parameters:
Port – Select from available port pins (PIN_A3, PIN_B3, etc.)
State – 0 or 1
Returns:
Undefined
Function:
This function will change the output state of a single port pin. If the data direction
for the pin selected was set to input, the direction is first set to output.
Example:
0x3, 0xA6, 0x2F, 0x1, 0x8B – Sets port pin PIN_A3 high.
0xA7 – Return Board ID
Parameters:
None
Returns:
5 bytes: “245PL”
Function:
This function will return the boardID.
Example:
0x1, 0xA7, A6 – Reads the board ID.
0xA8 – Setup A/D
Parameters:
Port Configuration – Selects analog port configuration. [See command 0xA8,
setup_AD() in the example firmware for options.]
A/D Conversion Clock – Select the source for the A/D conversion clock. [See
command 0xA8, setup_AD() in the example firmware for options.]
Returns:
Undefined
Function:
This function will select the input channel(s) and the source for the A/D
conversion clock. (Refer to the datasheet for the 18LF8722 for a detailed
explanation of the conversion clock.)
Example:
0x3, 0xA8, 0x00, 0x7, 0xAC – Sets all available A/D inputs on the DLP-245PL-G
to analog mode (0x00) and selects Fosc/64 for 20MHz operation (0x7).
0xA9 – A/D Conversion
Parameters:
Analog Port Number – Selects the analog port for the A/D conversion.
Returns:
2 Bytes: The 10-bit voltage data; LSB first.
Function:
This function will set the channel for the A/D conversion, pause 10uS, perform
the A/D conversion, and then return 2 bytes to the host (LSB first). Command
0xA8 must have been previously called to configure the desired analog channel
as an A/D input.
Example:
0x2, 0xA9, 0x2, 0xA8 – Selects analog channel 2 (AN2), performs the A/D
conversion, and returns 2 bytes of data.
相關PDF資料 |
PDF描述 |
|---|---|
| DLP-245SY-G | MODULE USB-MCU FT245RL W/SX48 |
| DLP-FPGA | MODULE USB-TO-FPGA TRAINING TOOL |
| DLP-HS-FPGA3 | MODULE USB-TO-FPGA SPARTAN 3A |
| DP83848CVVX/NOPB | TXRX ETHERNET PHYTER 48LQFP |
| DP83848HSQ/NOPB | IC TXRX ETHERNET PHYTER 40-LLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DLP-245PL-G-CCS | 功能描述:界面開發工具 DLP-245PL PACKAGED w/CCS Compiler RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| DLP-245SX | 功能描述:界面模塊 USB/Micro Dev Board RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-245SY | 功能描述:界面模塊 USB/Micro Dev Board RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-245SY-G | 功能描述:界面模塊 USB/Micro Dev Board RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| DLP-245SY-G-C | 功能描述:界面模塊 USB/Micro Dev Board W/GRICH C COMPILER RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。