參數資料
型號： DM6381F
廠商： Electronic Theatre Controls, Inc.
英文描述： V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
中文描述： .34綜合數據/傳真/語音/揚聲器調制解調器設備集
文件頁數： 16/40頁
文件大小： 341K
代理商： DM6381F
DM336P
V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
16
Final
Version: DM336P-DS-F02
August 15, 2000
d. DM6383 Configuration Modes
The DM6383A is power-on in jumpless mode. The
default configuration is set by loading the default
value stored in 93C46 to Auto-configuration register.
These values can be modified by software via the
logical device configuration registers in DM Jumpless
mode. This update value of new configuration is only
valid temporarily and will be lost after an active PC
Hardware Reset. Permanent changes of default
configuration will be done by informing micro-
controller to modify the content of 93C46 via Auto-
configuration Register.
The Plug and Play logic can operate through two
configuration modes: One is DM Jumpless mode, the
other, PnP mode. There are two operating methods
between the two modes: First, setting hard
configuration through Initiation Key sequences,
second, setting hard configuration according to the
register that is used, I/O Configuration Register or
Auto-configuration Register.
(1) The Initiation Key for Plug and Play
The Plug and Play logical is in sequence on powering
up and must be enabled by softwares. This is
achieved by a predefined series of writes (32 I/O
writes) to the Address port, which is called the
Initiation Key. The proper series of the I/O writes is
detected, then the Plug and Play read/write data ports
are enabled. The Write sequence will be reset and
must be issued from the beginning if any data
mismatch occurs. The exact sequence for Initiation
Key is listed below in hexadecimal notion.
(2) PnP Initiation Key
6A, B5, DA, ED, F6, FB, 7D, BE, DF, 6F, 37, 1B, 0D,
86, C3, 61, B0, 58, 2C, 16, 8B, 45, A2, D1, E8, 74,
3A, 9D, CE, E7, 73, 39
(3) DM Initiation Key
68, 34, 1A, 8D, CB, E3, 71, B8, 5C, 2E, 97, 4B, 25,
92, C9, E4, 72, B9, DC, 6E, B7, 5B, 2D, 96, CB, 65,
B2, D9, EC, 76, BB, 5D
(4) Isolation Protocol
A simple algorithm is used to isolate each Plug and
Play card. This algorithm uses the signals on the ISA
bus and requires lock-step operation between the
Plug and Play hardware and the isolation software.
STATE
ISOLATION
ID BIT = "1H"
SD[1:0] = "01"
LEAVE SD[7:0]
NO
GET ONE BIT FROM SERIAL IDENTIFIER
READ FROM SERIAL ISOLATION REGISTER
YES
WAIT FOR NEXT READ FROM SERIAL ISOLATION REGISTER
SD[1:0] = "10"
STATE
YES
ID = 0
READ ALL 72 BITS
DRIVE
AFTER I/O READ COMPLETES
ONE CARD
NO
YES
NO
YES
LEAVE SD[7:0]
NO
DRIVE "55H" ON SD[7:0]
相關PDF資料
PDF描述
DM6382F V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM6383F V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM336P V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM64ALS244BN Dual 4-Bit Non-Inverting Buffer/Driver
DM74ALS32MX Quad 2-input OR Gate
相關代理商/技術參數
參數描述
DM6382F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM6383F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V.34 Integrated Data/ Fax/Voice/Speakerphone Modem Device Set
DM63G 制造商:American Electronic Components / DURAKOOL 功能描述:Relay Socket Module 制造商:American Electronic Components / DURAKOOL 功能描述:RELAY SOCKET MODULE; Socket Mounting:Plug In; Voltage Rating:230V; Accessory Type:Relay Socket; Contact Voltage AC Max:230V; Contact Voltage DC Max:230V; Features:Green LED; For Use With:DZM2, DZM4, DZM90 & DZM92 Relays ;RoHS Compliant: Yes
DM644 LL-SUB-12-1F 制造商:Timesys Corporation 功能描述:LINUXLINK PRO EDITION FOR TI DAVINCI DM644X - Virtual or Non-Physical Inventory (Software & Literature)
DM6441ZWTARCL 制造商:Texas Instruments 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*