- 您現在的位置：買賣IC網 > PDF目錄376927 > DRM010 Vacuum Cleaner Designer Reference Manual PDF資料下載
參數資料
| 型號： | DRM010 |
| 英文描述： | Vacuum Cleaner Designer Reference Manual |
| 中文描述： | 吸塵器設計參考手冊 |
| 文件頁數： | 25/72頁 |
| 文件大?。?/td> | 1177K |
| 代理商： | DRM010 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Vacuum Cleaner Reference Design
Triac Drive Waveform
DRM010 — Rev 0
Designer Reference Manual
MOTOROLA
Vacuum Cleaner Reference Design
For More Information On This Product,
Go to: www.freescale.com
25
measured. The MCU’s ADC requires a 0- to 5-V analog signal.
Accurately measuring the load current would require a very small value
resistor and an operational amplifier with a low input-offset voltage.
Fortunately, the load current is not really needed for most applications.
Assume that the load current will lag the voltage for most inductive loads.
Vacuum cleaner universal motors are highly inductive.
When driving an inductive load, the current will lag the voltage. The triac
does not turn off at zero-voltage crossing. It will continue to conduct for
some degrees until the current passes through zero. As the phase angle
is increased, at some point, the current will become continuous. The
triac will be fired just after zero current crossing. As the phase angle is
increased further, approaching 180
°
, the triac will be fired before current
zero crossing. If a short pulse is used at these angles, the triac will not
conduct over the rest of the cycle, as shown in
Figure 1-9
. The end result
would be that the motor suddenly slows when the speed is turned all the
way up.
Figure 1-9
.
Undesirable Turn Off Using Short Pulse
TRIAC
FIRED
EARLY
TRIAC
TURNS
OFF
SHORT
PULSE
VOLTAGE
CURRENT
F
Freescale Semiconductor, Inc.
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| DRM011 | Direct Current Ignition Reference Design Designer Reference Manual |
| DRM013 | USB Security Key Reference Design Designer Reference Manual |
| DRM014 | USB and PS/2 Multimedia Keyboard Interface Reference DesignDesigner Reference Manual |
| DRM015 | USB Hub Keyboard for the MC68HC08KH12 Designer Reference Manual |
| DRM018 | 3-Phase PM Synchronous Motor Torque Vector Control Using 56F805 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DRM10 | 功能描述:DIP 開關/ SIP 開關 BCD 10 POS RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| DRM1004 | 功能描述:DIP 開關/ SIP 開關 ROTARY DIP SWITCH PLASTICSHAFT RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| DRM101 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Blood Pressure Monitor Using the Flexis QE128 Family |
| DRM10C | 功能描述:SWITCH DIP MINI SHAFT 10POS T/H RoHS:否 類別:開關 >> DIP 系列:DR 特色產品:RDM Series Rotary DIP Switch 標準包裝:70 系列:RDM 電路:十六進制 位置數:16 觸點額定電壓:0.1A @ 42VDC 觸動器類型:用于工具旋轉 觸動器電平:凹槽式 安裝類型:通孔 方向:頂部觸動 可清洗:是 其它名稱:EG4977-5RDMAR16PIT |
| DRM10C04 | 功能描述:編碼式波段開關 SW DIP MINI SHAFT 10POS T/H RoHS:否 制造商:C&K Components 位置數量:10 輸出代碼:Binary Coded Decimal 執行器:Screwdriver 觸點額定值: 端接類型:Solder Pin 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。