- 您現在的位置：買賣IC網 > PDF目錄376951 > DS1330YP-70-IND 256k Nonvolatile SRAM with Battery Monitor PDF資料下載
參數資料
| 型號： | DS1330YP-70-IND |
| 英文描述： | 256k Nonvolatile SRAM with Battery Monitor |
| 中文描述： | 256k非易失SRAM與電池監視器 |
| 文件頁數： | 2/11頁 |
| 文件大小： | 191K |
| 代理商： | DS1330YP-70-IND |
DS1330Y/AB
2 of 11
READ MODE
The DS1330 devices execute a read cycle whenever
WE
(Write Enable) is inactive (high) and
CE
(Chip
Enable) and
OE
(Output Enable) are active (low). The unique address specified by the 15 address inputs
(A
0
– A
14
) defines which of the 32,768 bytes of data is to be accessed. Valid data will be available to the
eight data output drivers within t
ACC
(Access Time) after the last address input signal is stable, providing
that
CE
and
OE
(Output Enable) access times are also satisfied. If
OE
and
CE
access times are not
satisfied, then data access must be measured from the later occurring signal (
CE
or
OE
) and the limiting
parameter is either t
CO
for
CE
or t
OE
for
OE
rather than address access.
WRITE MODE
The DS1330 devices execute a write cycle whenever the
WE
and
CE
signals are in the active (low) state
after address inputs are stable. The later-occurring falling edge of
CE
or
WE
will determine the start of
the write cycle. The write cycle is terminated by the earlier rising edge of
CE
or
WE
. All address inputs
must be kept valid throughout the write cycle.
WE
must return to the high state for a minimum recovery
time (t
WR
) before another cycle can be initiated. The
OE
control signal should be kept inactive (high)
during write cycles to avoid bus contention. However, if the output drivers are enabled (
CE
and
OE
active) then
WE
will disable the outputs in t
ODW
from its falling edge.
DATA RETENTION MODE
The DS1330AB provides full-functional capability for V
CC
greater than 4.75V and write protects by
4.5V. The DS1330Y provides full-functional capability for V
CC
greater than 4.5V and write protects by
4.25V. Data is maintained in the absence of V
CC
without any additional support circuitry. The NV
SRAMs constantly monitor V
CC
. Should the supply voltage decay, the NV SRAMs automatically write
protect themselves, all inputs become “don’t care,” and all outputs become high-impedance. As V
CC
falls
below approximately 2.7V, the power switching circuit connects the lithium energy source to RAM to
retain data. During power-up, when V
CC
rises above approximately 2.7V, the power switching circuit
connects external V
CC
to the RAM and disconnects the lithium energy source. Normal RAM operation
can resume after V
CC
exceeds 4.75V for the DS1330AB and 4.5V for the DS1330Y.
SYSTEM POWER MONITORING
DS1330 devices have the ability to monitor the external V
CC
power supply. When an out-of-tolerance
power supply condition is detected, the NV SRAMs warn a processor-based system of impending power
failure by asserting
RST
. On power-up,
RST
is held active for 200ms nominal to prevent system
operation during power-on transients and to allow t
REC
to elapse.
RST
has an open drain output driver.
BATTERY MONITORING
The DS1330 devices automatically perform periodic battery voltage monitoring on a 24-hour time
interval. Such monitoring begins within t
REC
after V
CC
rises above V
TP
and is suspended when power
failure occurs.
After each 24-hour period has elapsed, the battery is connected to an internal 1M test resistor for one
second. During this one second, if battery voltage falls below the battery voltage trip point (2.6V), the
battery warning output
BW
is asserted. Once asserted,
BW
remains active until the module is replaced.
The battery is still retested after each V
CC
power-up, however, even if
BW
is active. If the battery voltage
is found to be higher than 2.6V during such testing,
BW
is de-asserted and regular 24-hour testing
resumes.
BW
has an open drain output driver.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1330BL-70-IND | NVRAM (Battery Based) |
| DS1330WP-150 | NVRAM (Battery Based) |
| DS1330YL-100 | NVRAM (Battery Based) |
| DS1330YL-100-IND | NVRAM (Battery Based) |
| DS1330YL-70 | NVRAM (Battery Based) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1330YP-70IND+ | 功能描述:NVRAM 256K NV RAM w/Battery Monitor RoHS:否 制造商:Maxim Integrated 數據總線寬度:8 bit 存儲容量:1024 Kbit 組織:128 K x 8 接口類型:Parallel 訪問時間:70 ns 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 工作電流:85 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:EDIP 封裝:Tube |
| DS13320 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Color TV Owners Manual Manuel dinstructions du teleouleur Color TV Manual Del Propietario |
| DS1336 | 功能描述:IC AFTERBURNER 16-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - O 圈控制器 系列:- 標準包裝:1,000 系列:- 應用:電池備份，工業/汽車，大電流開關 FET 型:- 輸出數:5 內部開關:是 延遲時間 - 開啟:100ns 延遲時間 - 關閉:- 電源電壓:3 V ~ 5.5 V 電流 - 電源:250µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| DS1336N | 功能描述:IC AFTERBURNER IND 16-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - O 圈控制器 系列:- 標準包裝:1,000 系列:- 應用:電池備份，工業/汽車，大電流開關 FET 型:- 輸出數:5 內部開關:是 延遲時間 - 開啟:100ns 延遲時間 - 關閉:- 電源電壓:3 V ~ 5.5 V 電流 - 電源:250µA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR) |
| DS1336S | 功能描述:電源開關 IC - 配電 RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。