- 您現在的位置：買賣IC網 > PDF目錄9410 > DS1338U-33+ (Maxim Integrated Products)IC RTC 56BYTE NV RAM 3.3V 8-USOP PDF資料下載
參數資料
| 型號： | DS1338U-33+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC 56BYTE NV RAM 3.3V 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | 時鐘/日歷 |
| 特點： | 閏年，NVSRAM，方波輸出 |
| 存儲容量： | 56B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 3 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.3 V ~ 3.7 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 管件 |
| 產品目錄頁面： | 1433 (CN2011-ZH PDF) |
DS1338 I2C RTC with 56-Byte NV RAM
9 of 16
CLOCK ACCURACY
The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match between
the capacitive load of the oscillator circuit and the capacitive load for which the crystal was trimmed. Crystal
frequency drift caused by temperature shifts creates additional error. External circuit noise coupled into the
oscillator circuit can result in the clock running fast. Figure 4 shows a typical PC board layout for isolating the
crystal and oscillator from noise. Refer to Application Note 58: Crystal Considerations with Dallas Real-Time Clocks
for detailed information.
DS1338C ONLY
The DS1338C integrates a standard 32,768Hz crystal in the package. Typical accuracy at nominal VCC and +25°C
is approximately 10ppm. Refer to Application Note 58 for information about crystal accuracy vs. temperature.
Figure 4. Typical PC Board Layout for Crystal
RTC AND RAM ADDRESS MAP
Table 3 shows the address map for the RTC and RAM registers. The RTC registers and control register are located
in address locations 00h to 07h. The RAM registers are located in address locations 08h to 3Fh. During a multibyte
access, when the register pointer reaches 3Fh (the end of RAM space) it wraps around to location 00h (the
beginning of the clock space). On an I2C START, STOP, or register pointer incrementing to location 00h, the
current time and date is transferred to a second set of registers. The time and date in the secondary registers are
read in a multibyte data transfer, while the clock continues to run. This eliminates the need to re-read the registers
in case of an update of the main registers during a read.
CLOCK AND CALENDAR
The time and calendar information is obtained by reading the appropriate register bytes. See Figure 6 for the RTC
registers. The time and calendar are set or initialized by writing the appropriate register bytes. The contents of the
time and calendar registers are in the BCD format. Bit 7 of Register 0 is the clock halt (CH) bit. When this bit is set
to 1, the oscillator is disabled. When cleared to 0, the oscillator is enabled. The clock can be halted whenever the
timekeeping functions are not required, which minimizes VBAT current (IBATDAT) when VCC is not applied.
The day-of-week register increments at midnight. Values that correspond to the day of week are user-defined but
must be sequential (i.e., if 1 equals Sunday, then 2 equals Monday, and so on). Illogical time and date entries
result in undefined operation.
When reading or writing the time and date registers, secondary (user) buffers are used to prevent errors when the
internal registers update. When reading the time and date registers, the user buffers are synchronized to the
internal registers on any start or stop and when the register pointer rolls over to zero. The countdown chain is reset
LOCAL GROUND PLANE (LAYER 2)
CRYSTAL
X1
X2
GND
NOTE: AVOID ROUTING SIGNALS IN THE CROSSHATCHED
AREA (UPPER LEFT-HAND QUADRANT) OF THE PACKAGE
UNLESS THERE IS A GROUND PLANE BETWEEN THE SIGNAL
LINE AND THE PACKAGE.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-23X-MX-B1 | CONVERTER MOD DC/DC 5.2V 75W |
| DS1338Z-33+ | IC RTC 56BYTE NV RAM 3.3V 8-SOIC |
| VI-222-MW | CONVERTER MOD DC/DC 15V 100W |
| VI-221-MW | CONVERTER MOD DC/DC 12V 100W |
| VE-B3Z-MV-B1 | CONVERTER MOD DC/DC 2V 60W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1338U-33/T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 56BYTE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C Serial RTC w/56 Byte NV RAM |
| DS1338U-33/T&R | 功能描述:實時時鐘 I2C Serial RTC w/56 Byte NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1338U-33+ | 功能描述:實時時鐘 I2C Serial RTC w/56 Byte NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1338U-33+ | 制造商:Maxim Integrated Products 功能描述:IC RTC YY-MM-DD 56 X 8 OP-8 |
| DS1338U-33+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 56BYTE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC 56BYTE NV RAM 3.3V 8-USOP 制造商:Maxim Integrated Products 功能描述:Real Time Clock I2C Serial RTC w/56 Byte NV RAM |
發布緊急采購，3分鐘左右您將得到回復。