- 您現在的位置：買賣IC網 > PDF目錄9330 > DS1384FP-12 (Maxim Integrated Products)IC CTRLR RTC WDOG 120NS 44-MQFP PDF資料下載
參數資料
| 型號： | DS1384FP-12 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/18頁 |
| 文件大小： | 0K |
| 描述： | IC CTRLR RTC WDOG 120NS 44-MQFP |
| 標準包裝： | 96 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，方波輸出，監視計時器 |
| 存儲容量： | 50B |
| 時間格式： | HH:MM:SS:hh（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 并聯 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 2.4 V ~ 4 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | DS1384FP12 |
DS1384
4 of 18
PIN
NAME
FUNCTION
38
VCC
DC Power Input. DC operating voltage is provided to the device on
this pin. VCC is the +5V input.
39
INTA
Active-Low Interrupt Output A.
INTA can be programmed as a time-
of-day alarm or as a watchdog alarm. (
INTB becomes the alternate
function).
INTA can also be programmed to output either a pulse or a
level.
42, 43
X1, X2
Connections for Standard 32.768kHz Quartz Crystal. When ordering,
request a load capacitance (CL) of 6pF. The internal oscillator circuitry
is designed for operation with a crystal having a specified load
capacitance of 6pF. For more information on crystal selection and
crystal layout considerations, refer to Application Note 58: Crystal
Considerations with Dallas Real Time Clocks.
ADDRESS DECODING
The DS1384 accommodates 17 address lines, which allows direct connection of up to 128k bytes of static
RAM. The lower 14 bytes of RAM, regardless of the density used, will always contain the timekeeping,
alarm, and watchdog registers. The 14 clock registers reside in the lower 14 RAM locations without
conflict by inhibiting the
OER (output enable RAM) signal during clock access. Since the watchdog
timekeeping chip actually contains 64 registers (14 RTC and 50 user RAM), the lower 64 bytes of any
attached memory resides within the DS1384. However, the RAM’s physical location is transparent to the
user and the memory map looks continuous from the first clock address to the upper most attached RAM
address.
OPERATION—READ CYCLE
The DS1384 executes a read cycle whenever
WE is inactive (high) and CE and OE are active (low). The
unique address specified by the address inputs (A0-A16) defines which of the on-chip 64 RTC/RAM or
external SRAM locations is to be accessed. When the address value presented to the DS1384 is in the
range of 00000H through 0003FH, one of the 64 on-chip registers will be selected and valid data will be
available to the eight data output drivers within tACC (access time) after the address input signal is stable,
providing that the
CE and OE access times are also satisfied. If they are not, then data access must be
measured from the latter occurring signal (
CE or OE) and the limiting parameter is either tCO for CE or
tOE for OE rather than the address access time. When one of the on-chip registers is selected for read, the
OER signal will remain inactive throughout the read cycle.
When the address value presented to the DS1384 is in the range of 00040H through 1FFFFH, an external
SRAM location will be selected. In this case the
OE signal will be passed to the OER pin, with the
specified delay times of tAOEL or tOERL.
OPERATION—WRITE CYCLE
The DS1384 is in the write mode whenever the
WE (Write Enable) and CE (Chip Enable) signals are in
the active (low) state after the address inputs are stable. The latter occurring falling edge of
CE or WE
will determine the start of the write cycle. The write cycle is terminated by the earlier rising edge of
CE
or
WE. All address inputs must be kept valid throughout the write cycle. WE must return to the high state
for a minimum recovery state (tWR) before another cycle can be initiated. Data must be valid on the data
bus with sufficient Data Set Up (tDS) and Data Hold Time (tDH) with respect to the earlier rising edge of
CE or WE. The OE control signal should be kept inactive (high) during write cycles to avoid bus
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2NR-MY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
| VE-BN4-IU-F2 | CONVERTER MOD DC/DC 48V 200W |
| DS1305E | IC RTC SERIAL ALARM 20-TSSOP |
| VE-BN4-IU-F1 | CONVERTER MOD DC/DC 48V 200W |
| VI-2NP-MY-F4 | CONVERTER MOD DC/DC 13.8V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1384FP-12+ | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1384FP-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Real-Time Clock |
| DS1384T-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Real-Time Clock |
| DS1384T-150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Real-Time Clock |
| DS1385 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Real Time Clock 4K x 8 |
發布緊急采購，3分鐘左右您將得到回復。