- 您現在的位置：買賣IC網 > PDF目錄9361 > DS1670E/T&R (Maxim Integrated Products)IC CTRLR SYSTEM PORTABLE 20TSSOP PDF資料下載
參數資料
| 型號： | DS1670E/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CTRLR SYSTEM PORTABLE 20TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 便攜系統控制器 |
| 特點： | 警報器，閏年，監視計時器 |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | 3 線串口 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 電壓 - 電源，電池： | 2.5 V ~ 3.7 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
DS1670
3 of 16
PIN DESCRIPTION
PIN
NAME
FUNCTION
1
VBAT
Battery Input for Standard 3V Lithium Cell or Other Energy Source. UL recognized to
ensure against reverse charging when used with a lithium battery. Go to www.maxim-
ic.com/qa/info/ul/.
2
VCCO
External SRAM Power Supply Output. This pin is internally connected to VCC when VCC is
within nominal limits. However, during power-fail VCCO is internally connected to the
VBAT pin. Switchover occurs when VCC drops below the lower of VBAT or 2.7V.
3
SCLK
Serial Clock Input. Used to synchronize data movement on the serial interface.
4
I/O
Data Input/Output. This pin is the bidirectional data pin for the 3-wire interface.
5
CS
Chip Select. Must be asserted high during a read or a write for communication over the 3-
wire serial interface. CS has an internal 40k
pulldown resistor.
6
CEI
RAM Chip-Enable In. Must be driven low to enable the external RAM.
7
CEOL
RAM Chip-Enable Out Low. Active-low chip-enable output for low-order SRAM byte.
8
CEOH
RAM Chip-Enable Out High. Active-low chip-enable output for high-order SRAM byte.
9
INT
Interrupt Output. This pin is an active-high output that can be used as an interrupt input to
a microprocessor. The INT output remains high as long as the status bit causing the
interrupt is present and the corresponding interrupt-enable bit is set. The INT pin operates
when the DS1670 is powered by VCC or VBAT.
10
GND
Ground. DC power is provided to the device on this pin.
11
BHE
Byte High-Enable Input. This pin when driven low activates the
CEOH output if CEI is
also driven low.
12
BLE
Byte Low-Enable Input. This pin when driven low activates the
CEOL output if CEI is
also driven low.
13
RST
Active-Low Reset. The
RST pin functions as a microprocessor reset signal. This pin is
driven low 1) when VCC is outside of nominal limits; 2) when the watchdog timer has
timed out; 3) during the power up reset period; and 4) in response to a pushbutton reset.
The
RST pin also functions as a pushbutton reset input. When the RST pin is driven low,
the signal is debounced and timed such that a
RST signal of at least 250ms is generated.
This pin has an open-drain output with an internal 47k
pullup resistor.
14,
15, 16
AIN2,
AIN1,
AIN0
Analog Inputs. These pins are the three analog inputs for the 3-channel ADC.
17, 18
X2, X1
Connections for Standard 32.768kHz Quartz Crystal. For greatest accuracy, the DS1670
must be used with a crystal that has a specified load capacitance of 6pF. There is no need
for external capacitors or resistors. Note: X1 and X2 are very high-impedance nodes. It is
recommended that they and the crystal be guard-ringed with ground and that high
frequency signals be kept away from the crystal area. For more information on crystal
selection and crystal layout considerations, refer to Application Note 58: Crystal
Considerations with Dallas Real Time Clocks. The DS1670 does not function without a
crystal.
19
VCC
+3.3V Input DC Power. When 3.3V is applied within nominal limits, the device is fully
accessible and data can be written and read. When VCC drops below 2.88V (typical) access
to the device is prohibited. When VCC drops below the lower of VBAT and 2.7V (typical),
the device is switched over to the backup power supply.
20
ST
Active-Low Strobe Input. The strobe input pin is used with the watchdog timer. If the
ST
pin is not driven low within the watchdog time period, the
RST pin is driven low.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1305EN | IC RTC SERIAL ALARM IND 20-TSSOP |
| MAX5455EUD+ | IC DGTL POT DUAL 256-TAP 14TSSOP |
| DS1501WZ+T&R | IC RTC WDOG Y2KC 3.3V 28-SOIC |
| MAX5410EEE+ | IC DGTL POT DUAL AUDIO 16-QSOP |
| D38999/26FH21PD | CONN PLUG 21POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1670S | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1670S+ | 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1671H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver |
| DS1671J-8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver |
| DS-1671ZJ | 制造商:Hikvision USA 功能描述:4" Indoor Ceiling Embedded Mount |
發布緊急采購，3分鐘左右您將得到回復。