參數資料
型號: DS1670E/T&R
廠商: Maxim Integrated Products
文件頁數: 16/16頁
文件大?。?/td> 0K
描述: IC CTRLR SYSTEM PORTABLE 20TSSOP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: 便攜系統控制器
特點: 警報器,閏年,監視計時器
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: 3 線串口
電源電壓: 2.97 V ~ 3.63 V
電壓 - 電源,電池: 2.5 V ~ 3.7 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-TSSOP
包裝: 帶卷 (TR)
DS1670
9 of 16
input that is selected by these 2 bits. Note also that the converter can be turned off by these bits to reduce
power. When the ADC is turned on by setting AIS0 and AIS1 to any value other than 0,0 the analog input
voltage is converted and written to the ADC Register within 488ms. An internal analog filter at the input
reduces high frequency noise. Subsequent updates occur approximately every 10ms. If AIS0 and/or AIS1
are changed, updates will occur at the next 10ms conversion time.
The Conversion Update In Progress (CU) bit in the Status Register indicates when the ADC Register can
be read. When this bit is a 1, an update to the ADC Register will occur within 488ms maximum.
However, when this bit is 0 an update will not occur for at least 244ms. The CU bit should be polled
before reading the ADC Register to ensure that the contents are stable during a read cycle. Once a read
cycle to the ADC Register has been started, the DS1670 will not update that register until the read cycle
has been completed. It should also be mentioned that taking CS low will abort the read cycle and will
allow the ADC Register to be updated.
Figure 6 illustrates the timing of the CU bit relative to an instruction to begin conversion and the
completion of that conversion.
CU BIT TIMING Figure 6
3-WIRE SERIAL INTERFACE
Communication with the DS1670 is accomplished through a simple 3-wire interface consisting of the
Chip Select (CS), Serial Clock (SCLK) and Input/Output (I/O) pins.
All data transfers are initiated by driving the CS input high. The CS input serves two functions. First, CS
turns on the control logic, which allows access to the shift register for the address/command sequence.
Second, the CS signal provides a method of terminating either single byte or multiple byte (burst) data
transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For data input, data must
be valid during the rising edge of the clock and data bits are output on the falling edge of the clock. If the
CS input goes low, all data transfer terminates and the I/O pin goes to a high-impedance state.
相關PDF資料
PDF描述
DS1305EN IC RTC SERIAL ALARM IND 20-TSSOP
MAX5455EUD+ IC DGTL POT DUAL 256-TAP 14TSSOP
DS1501WZ+T&R IC RTC WDOG Y2KC 3.3V 28-SOIC
MAX5410EEE+ IC DGTL POT DUAL AUDIO 16-QSOP
D38999/26FH21PD CONN PLUG 21POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
DS1670S 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1670S+ 功能描述:實時時鐘 Portable System Controller RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1671H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver
DS1671J-8 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Clock Driver
DS-1671ZJ 制造商:Hikvision USA 功能描述:4" Indoor Ceiling Embedded Mount