參數資料
型號: DS1678S+
廠商: Maxim Integrated Products
文件頁數: 15/25頁
文件大小: 0K
描述: IC REAL TIME EVENT REC 8-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 88
類型: 時間事件記錄器
特點: 警報器,閏年,NVSRAM,Y2K
存儲容量: 32B
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: I²C,2 線串口
電源電壓: 4.5 V ~ 5.5 V
電壓 - 電源,電池: 2.6 V ~ 3.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.209",5.30mm 寬)
供應商設備封裝: 8-SO
包裝: 管件
產品目錄頁面: 1434 (CN2011-ZH PDF)
DS1678 Real-Time Event Recorder
22 of 25
SECURITY
The DS1678 provides several measures to ensure data integrity for the end user. These security measures
are intended to prevent third-party intermediaries from tampering with the data that has been stored in the
event-log memory.
As a first security measure, the event-log memory is read-only from the perspective of the end user. The
DS1678 can write the data into these memory banks, but the end user cannot write data to individual
registers. This prevents an unscrupulous intermediary from writing false data to the DS1678. The end
user, however, can clear the contents of the event-log memory. A new mission cannot be started unless
the MEM CLR bit has been set to one to indicate that the memory and registers are cleared.
As a second security measure, changing any value in the memory including the RTC and control registers
stops event logging and clears the MIP and ME bits. The MEM CLR bit must be set to one so the
memory and registers are cleared before a new event-log mission can begin.
I
2C SERIAL DATA BUS
The DS1678 supports a bidirectional I2C bus and data transmission protocol. A device that sends data
onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that controls
the message is called a “master.” The devices that are controlled by the master are “slaves.” The bus must
be controlled by a master device that generates the serial clock (SCL), controls the bus access, and
generates the START and STOP conditions. The DS1678 operates as a slave on the I2C bus. Connections
to the bus are made via the open-drain I/O lines SDA and SCL.
The following bus protocol has been defined (Figure 6):
Data transfer can be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in
the data line while the clock line is HIGH are interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy: Both data and clock lines remain HIGH.
Start data transfer: A change in the state of the data line, from HIGH to LOW, while the clock is HIGH,
defines a START condition.
Stop data transfer: A change in the state of the data line, from LOW to HIGH, while the clock line is
HIGH, defines the STOP condition.
Data valid: The state of the data line represents valid data when, after a START condition, the data line
is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed
during the LOW period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited, and is determined
by the master device. The information is transferred byte-wise and each receiver acknowledges with a
ninth bit. Within the bus specifications a standard mode (100kHz clock rate) and a fast mode (400kHz
clock rate) are defined. The DS1678 works in both modes.
Acknowledge: Each receiving device, when addressed, is obliged to generate an acknowledge after the
reception of each byte. The master device must generate an extra clock pulse which is associated with this
acknowledge bit.
相關PDF資料
PDF描述
DS1685EN-3+ IC RTC 3V 64BIT Y2KC IND 24TSSOP
DS1374C-33# IC RTC I2C W/CHARGER 16-SOIC
MCP4562T-103E/MF IC DGTL POT 10K 256TAPS 8-DFN
D38999/24MA98SN CONN RCPT 3POS JAM NUT W/SCKT
MS27467T23F35PD CONN PLUG 100POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
DS1678S/T&R 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 32BYTE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RECORDER REALTIME EVENT 8SOIC
DS1678S/T&R 功能描述:IC RECORDER REALTIME EVENT 8SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器,閏年,SRAM 存儲容量:- 時間格式:HH:MM:SS(12/24 小時) 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源,電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件
DS1678S+ 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS1678S+T&R 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 32BYTE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC REAL TIME EVENT REC 8-SOIC 制造商:Maxim Integrated Products 功能描述:Real Time Clock Real-Time Event Recorder
DS1678S+T&R 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube