- 您現在的位置：買賣IC網 > PDF目錄9405 > DS1678S+ (Maxim Integrated Products)IC REAL TIME EVENT REC 8-SOIC PDF資料下載
參數資料
| 型號： | DS1678S+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC REAL TIME EVENT REC 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 88 |
| 類型： | 時間事件記錄器 |
| 特點： | 警報器，閏年，NVSRAM，Y2K |
| 存儲容量： | 32B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電壓 - 電源，電池： | 2.6 V ~ 3.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 產品目錄頁面： | 1434 (CN2011-ZH PDF) |
DS1678 Real-Time Event Recorder
17 of 25
SPECIAL-PURPOSE REGISTERS
The following descriptions define the operation of the DS1678 special-purpose registers.
CONTROL REGISTER (0Eh)
MSB
LSB
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
ME
CLR
DIS1
DIS0
RO
TR1
TR0
EOSC
Bit 7: Mission Enable (ME). This bit enables the device to begin a mission. The ME bit cannot be
written to one unless the MEM CLR bit in the Status Register is one, signifying that the memory and
registers have been cleared. With the ME bit set to one, the device waits for the first event to occur (
INT
is activated). Once that first event occurs, the MIP bit is set, the time/date stamp is recorded in the Start
Time Stamp Register, the Event 0 Rollover Stamp is written to zero, the Event Counter Register is
incremented, and the ETC begins incrementing.
When the ME bit is set to logic zero, the DS1678 waits until a one is written to the MIP bit via the I2C
interface to start the mission. When the MIP bit is written to one, the ME bit is set to one, the current
time/date is recorded in the Start Time Stamp register, the Event 0 Rollover Stamp is written to zero, the
Event Counter Register is incremented, and the ETC begins incrementing.
The ME bit is automatically written to zero whenever a mission is stopped.
Bit 6: Clear Enable (CLR). This bit enables the memory to be cleared. When this bit is set to logic one
and the clear memory (CM) bit is subsequently set to one, the Event-Log Memory, Event Counter, and
Start Time Stamp registers are all cleared to zeros. Following the writing of a one to the ME bit, the CLR
bit is also set to logic zero, and the MEM CLR bit is set to logic one. If the clear enable bit is set, but a
command other than writing a one to the clear memory bit is issued next, the CLR bit is cleared to zero
and the contents of the Event-Log, Start Time Stamp, and Event Counter registers are unchanged.
Bits 5 and 4: Duration Interval Select 1 and 0 (DIS1 and DIS0). These bits select the amount of time
between increments of the ETC that is used to determine the amount of time between events. After the
first event is recorded, all subsequent events are recorded as the elapsed time since the previous event.
When a subsequent event occurs, the ETC value is stored in the event-log memory.
To obtain the maximum accuracy of the event logger, the smallest possible resolution of the ETC should
be selected. The expected maximum time between events must also be taken into account to get the full
1025 events logged, because when the ETC count reaches 65,535 increments, if the next event has not
occurred by that point, FFFFh is written into the memory, the ETC rolls over to 0000h and continues to
count until the next event occurs or FFFFh is reached again. Whenever FFFFh is reached by the ETC, it
stores that value in event-log memory, resets to 0000h, continues counting, and the memory address
pointer increments to the next memory location. Whenever an FFFFh appears in the memory, the next
two bytes of data are part of the elapsed time for the same event, even if the value in the next two bytes of
memory are 0000h, which means that an event occurred at time increment FFFFh. To recover the total
elapsed time between events when FFFFh is in the event-log memory; add the contents of the next two
bytes to the FFFFh. If the next two bytes are 0000h, indicating that the event occurred at FFFFh, add the
0000h to FFFFh to get FFFFh. If the next two bytes are 0100h, add 0100h to FFFFh to get 100FFh. This
相關PDF資料 |
PDF描述 |
|---|---|
| DS1685EN-3+ | IC RTC 3V 64BIT Y2KC IND 24TSSOP |
| DS1374C-33# | IC RTC I2C W/CHARGER 16-SOIC |
| MCP4562T-103E/MF | IC DGTL POT 10K 256TAPS 8-DFN |
| D38999/24MA98SN | CONN RCPT 3POS JAM NUT W/SCKT |
| MS27467T23F35PD | CONN PLUG 100POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1678S/T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 32BYTE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RECORDER REALTIME EVENT 8SOIC |
| DS1678S/T&R | 功能描述:IC RECORDER REALTIME EVENT 8SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器，閏年，SRAM 存儲容量:- 時間格式:HH:MM:SS（12/24 小時） 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源，電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件 |
| DS1678S+ | 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1678S+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 32BYTE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC REAL TIME EVENT REC 8-SOIC 制造商:Maxim Integrated Products 功能描述:Real Time Clock Real-Time Event Recorder |
| DS1678S+T&R | 功能描述:實時時鐘 Real-Time Event Recorder RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。