- 您現在的位置：買賣IC網 > PDF目錄9189 > DS1841X (Maxim Integrated Products)IC RES LOG NV I2C DGTL 10TDFN PDF資料下載
參數資料
| 型號： | DS1841X |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RES LOG NV I2C DGTL 10TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 接片： | 128 |
| 電阻（歐姆）： | 22k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±250 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 模具 |
| 供應商設備封裝： | 模具 |
| 包裝： | 管件 |
DS1841
Temperature-Controlled, NV, I2C,
Logarithmic Resistor
14
______________________________________________________________________________________
Byte read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition, and the master transmits an ACK using
the bit write definition to receive additional data bytes.
The master must NACK the last byte read to terminate
communication so the slave returns control of SDA to
the master.
Slave address byte: Each slave on the I2C bus
responds to a slave address byte sent immediately fol-
lowing a START condition. The slave address byte con-
tains the slave address in the most significant 7 bits
and the R/W bit in the least significant bit.
The DS1841’s slave address is determined by the state
of the A0 and A1 address pins as shown in Figure 2.
Address pins tied to GND result in a 0 in the corre-
sponding bit position in the slave address. Conversely,
address pins tied to VCC result in a 1 in the corre-
sponding bit positions.
When the R/W bit is 0 (such as in 50h), the master is
indicating that it will write data to the slave. If R/W = 1
(51h in this case), the master is indicating that it wants
to read from the slave.
If an incorrect slave address is written, the DS1841
assumes the master is communicating with another I2C
device and ignores the communication until the next
START condition is sent.
Memory address: During an I2C write operation, the
master must transmit a memory address to identify the
memory location where the slave is to store the data.
The memory address is always the second byte trans-
mitted during a write operation following the slave
address byte.
I2C Communication
Writing a single byte to a slave: The master must gen-
erate a START condition, write the slave address byte
(R/W = 0), write the memory address, write the byte of
data, and generate a STOP condition. Remember the
master must read the slave’s acknowledgment during
all byte write operations.
When writing to the DS1841, the potentiometer adjusts to
the new setting once it has acknowledged the new data
that is being written, and the EEPROM is written following
the STOP condition at the end of the write command. To
change the setting without changing the EEPROM, termi-
nate the write with a repeated START condition before
the next STOP condition occurs. Using a repeated
START condition prevents the tW delay required for the
EEPROM write cycle to finish.
SDA
SCL
tHD:STA
tLOW
tHIGH
tR
tF
tBUF
tHD:DAT
tSU:DAT
REPEATED
START
tSU:STA
tHD:STA
tSU:STO
tSP
STOP
NOTE: TIMING IS REFERENCE TO VIL(MAX) AND VIH(MIN).
START
Figure 3. I2C Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2V2-MX-B1 | CONVERTER MOD DC/DC 15V 75W |
| VI-2V3-MX-B1 | CONVERTER MOD DC/DC 24V 75W |
| DS3501U+T&R | IC POT NV 128POS HV 10-USOP |
| DS3502U+T&R/C | IC POT DGTL NV 128TAP 10-USOP |
| DS3502U+T&R | IC POT DGTL NV 128TAP 10-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1842 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
| DS1842A | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
| DS1842AN+ | 功能描述:電流和電力監控器、調節器 76V APD Bias Output Stage w/Current Mtr RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel |
| DS1842AN+T&R | 制造商:Maxim Integrated Products 功能描述:76V, APD, BIAS OUTPUT STAGE WITH CURRENT MONITORING - Tape and Reel |
| DS1842AN+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
發布緊急采購，3分鐘左右您將得到回復。