Address Inputs, A0, A1, and A2, should be tied to either VCC or GND" />
參數資料
型號: DS1844S-100/T&R
廠商: Maxim Integrated Products
文件頁數: 2/14頁
文件大小: 0K
描述: IC POT DIG QUAD 100K 20-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1,000
接片: 64
電阻(歐姆): 100k
電路數: 4
溫度系數: 標準值 750 ppm/°C
存儲器類型: 易失
接口: 2 線串行(設備位址)或 5 線串行
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 20-SOIC W
包裝: 帶卷 (TR)
DS1844
10 of 14
11.
Address Inputs, A0, A1, and A2, should be tied to either VCC or GND depending on the desired
address selections.
12.
Resistor inputs cannot go below GND by more than 0.5 volts or above VCC by more than 0.5
volts.
13.
-3dB cutoff frequency characteristics for the DS1844 depend on potentiometer total resistance:
DS1844-010; 1 MHz; DS1844-050; 200 kHz; DS1844-100; 100 kHz.
14.
See Figure 3, 5-wire timing diagram.
15.
For 5-wire control logic and VCC = 5V ±10%, maximum VIL = +0.8V. For VCC = 3.0V ±10%,VIL
= +0.6V.
16.
Absolute linearity is used to measure expected wiper voltage versus measured wiper voltage as
determined by wiper position. The DS1844 is specified to provide an absolute linearity of ± 0.5
LSB.
17.
Relative linearity is used to determine the change in wiper voltage between two adjacent wiper
positions. The DS1844 is specified to provide a relative linearity of ± 0.25 dB.
18.
When used as a rheostat or variable resistor the temperature coefficient applies: 650 ppm/°C.
When used as a voltage divider or potentiometer, the effective temperature coefficient approaches
30 ppm/°C.
19.
Maximum ICC active current is dependent on clock rates during serial port activity. Maximum
ICC active current is specified for 5 MHz clock rates, and worse case input logic levels.
20.
tSETUP is the minimum time required for the port select input, PS, to be stable before any activity
on SDA or SCL terminals.
21.
tSETUP is the minimum time required for the port select input, PS, and/or the R/ W input to be
stable before RST becomes active (or goes to a high state).
22.
See Figure 8, 5-wire timing diagram.
23.
Measured with load as shown in Figure 9.
24.
Valid for VCC = 5V only.
25.
Valid at 25
°C only.
相關PDF資料
PDF描述
DS1845E-100/T&R IC POT/MEM DUAL NV 100K 14-TSSOP
DS1846E-010+T&R IC NV TRI-POT MEM MON 20TSSOP
DS1847E-010/T&R IC RES TEMP-CNTRL 10/10K 14TSSOP
DS1848B-C10+ IC RES/MEM TEMP 10/10K 16-CSBGA
DS1852B-000/T&R IC MONITOR TXRX OPTICAL 25-BGA
相關代理商/技術參數
參數描述
DS1845 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual NV Potentiometer and Memory
DS1845B-010 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1845B-010/T&R 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1845B-010+ 功能描述:數字電位計 IC Dual NV w/Memory RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1845B-010+T&R 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 100/256POS 10KOHM DUAL 16CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT/MEM DUAL NV 10K 16-BGA