- 您現在的位置：買賣IC網 > PDF目錄9179 > DS1845E-100+T&R (Maxim Integrated Products)IC POT/MEM DUAL NV 100K 14-TSSOP PDF資料下載
參數資料
| 型號： | DS1845E-100+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT/MEM DUAL NV 100K 14-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 100，256 |
| 電阻（歐姆）： | 10k，100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
DS1845
7 of 14
The DS1845 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL respectively. After
each byte is received, an acknowledge bit is transmitted.
START and STOP conditions are
recognized as the beginning and end of a serial transfer. Address recognition is performed by
hardware after reception of the slave (device) address and direction bit.
2. Slave transmitter mode: The 1st byte is received and handled as in the slave receiver mode. However,
in this mode the direction bit will indicate that the transfer direction is reversed. Serial data is
transmitted on SDA by the DS1845 while the serial clock is input on SCL. START and STOP
conditions are recognized as the beginning and end of a serial transfer.
Slave Address: command/control byte is the 1st byte received following the START condition from the
master device. The command/control byte consists of a 4-bit control code. For the DS1845, this is set as
1010 binary for read/write operations. The next 3 bits of the command/ control byte are the device select
bits or slave address (A2, A1, A0). They are used by the master device to select which of eight devices is
to be accessed. When reading or writing the DS1845, the device-select bits must match the device-select
pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to be performed.
When set to a 1 a read operation is selected, and when set to a 0 a write operation is selected.
Following the START condition, the DS1845 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 1010 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an acknowledge signal on the SDA line.
WRITE PROTECT
An external pin WP (write protect) protects EEPROM data and potentiometer position from alteration in
an application. This pin must be open or tied high to protect data from alteration.
READING AND WRITING THE POTENTIOMETER VALUES
Reading from and writing to the potentiometers consists of a standard read or write to EEPROM memory
at the addresses F8h and F9h. The 8-bit value at address F9h controls the wiper setting for potentiometer
0, which has 100 positions. The 8-bit value at address F8h controls the wiper setting of potentiometer 1,
which has 256 positions. Potentiometer 1 may be set to any value between 00h and FFh. 00h sets the
wiper of potentiometer 1 to its lowest value and FFh sets the wiper to its highest. Potentiometer 0 may be
set to any value between 00h and 63h. A value of 00h sets the wiper of potentiometer 0 to its lowest
position and 63h sets the wiper to its highest position. Any hexadecimal value is a valid address. Setting
a value greater than the upper limit of the potentiometer’s range, 64h or greater for potentiometer 0, will
result in setting the wiper to its highest position, but the MSB will be ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| P3P25814AG-08SR | IC CLOCK GEN 16-128MHZ 8-SOIC |
| 7SB3126BMX1TCG | 1 BIT BUS SWITCH 6UDFN |
| DS1855E-050+T&R | IC RES TEMP-CNTRL 10/50K 14TSSOP |
| DS1855E-010+T&R | IC RES TEMP-CNTRL 10/10K 14TSSOP |
| 7SB3257MUTCG | 1 BIT MUX/DEMUX BUS SWTCH UDFN6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1845E-50+T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT & MEM LEAD FREE - Tape and Reel |
| DS1845X-010 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual NV Potentiometer and Memory |
| DS1845X-010/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV POT AND MEM BUMP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT/MEM DUAL NV 10K 14-FCP |
| DS1845X-010/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1845X-050 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual NV Potentiometer and Memory |
發布緊急采購，3分鐘左右您將得到回復。