- 您現在的位置：買賣IC網 > PDF目錄9179 > DS1855E-050+T&R (Maxim Integrated Products)IC RES TEMP-CNTRL 10/50K 14TSSOP PDF資料下載
參數資料
| 型號： | DS1855E-050+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/21頁 |
| 文件大小： | 0K |
| 描述： | IC RES TEMP-CNTRL 10/50K 14TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 100，256 |
| 電阻（歐姆）： | 10k，50k，100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
DS1855
15 of 21
NOTES:
1. All voltages are referenced to ground.
2. ISTBY specified with for VCC = 3.0V and 5.0V, and control port logic pins are driven to the appropriate
logic levels. Appropriate logic levels specify that logic inputs are within a 0.5V of ground or VCC for
the corresponding inactive state.
3. I/O pins of fast mode devices must not obstruct the SDA and SCL lines if VCC is switched off.
4. A fast mode device can be used in a standard mode system, but the requirement t
SU:DAT > 250ns must
then be met. This will automatically be the case if the device does not stretch the LOW period of the
SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next
data bit to the SDA line tRMAX + tSU:DAT = 1000 + 250 = 1250ns before the SCL line is released.
5. After this period, the first clock pulse is generated.
6. The maximum t
HD:DAT has only to be met if the device does not stretch the LOW period (tLOW) of the
SCL signal.
7. CB – Total capacitance of one bus line in picofarads, timing referenced to 0.9 x V
CC and 0.1 x VCC.
8. EEPROM write begins after a STOP condition occurs.
9. Absolute linearity is used to measure expected wiper voltage as determined by wiper position.
10. Relative linearity is used to determine the change of wiper voltage between two adjacent wiper
positions.
11. ICC specified with SDA pin open.
12. Maximum ICC is dependent on clock rates.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1855E-010+T&R | IC RES TEMP-CNTRL 10/10K 14TSSOP |
| 7SB3257MUTCG | 1 BIT MUX/DEMUX BUS SWTCH UDFN6 |
| P3P25812AG-08SR | IC CLOCK GEN 8-64MHZ 8-SOIC |
| VE-BW2-MY-F2 | CONVERTER MOD DC/DC 15V 50W |
| VE-BW2-MY-F1 | CONVERTER MOD DC/DC 15V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1855E-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-100/R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-100/T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-100/T&R | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Nonvolatile Digital Potentiometer and Secure Memory |
| DS1855E-C01/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。