參數資料
型號： DS21352LN+
廠商： Maxim Integrated Products
文件頁數： 76/137頁
文件大?。?/td> 0K
描述： IC TXRX T1 1-CHIP 3.3V 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
功能： 單芯片收發器
接口： HDLC，T1
電路數： 1
電源電壓： 3.14 V ~ 3.47 V
電流 - 電源： 75mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
包括： DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器
產品目錄頁面： 1429 (CN2011-ZH PDF)
DS21352/DS21552
43 of 137
7. STATUS AND INFORMATION REGISTERS
There is a set of nine registers that contain information on the current real time status of the device, Status
Register 1 (SR1), Status Register 2 (SR2), Receive Information Registers 1 to 3 (RIR1/RIR2/RIR3) and a
set of four registers for the onboard HDLC and BOC controller. The specific details on the four registers
pertaining to the HDLC controller are covered in Section 15.3.2 but they operate the same as the other
status registers in the DS21352/552 and this operation is described below.
When a particular event has occurred (or is occurring), the appropriate bit in one of these nine registers
will be set to a one. All of the bits in SR1, SR2, RIR1, RIR2, and RIR3 registers operate in a latched
fashion. This means that if an event or an alarm occurs and a bit is set to a one in any of the registers, it
will remain set until the user reads that bit. The bit will be cleared when it is read and it will not be set
again until the event has occurred again (or in the case of the RBL, RYEL, LRCL, and RLOS alarms, the
bit will remain set if the alarm is still present). There are bits in the four HDLC status registers that are
not latched and these bits are listed in Section 15.3.2.
The user will always proceed a read of any of the nine registers with a write. The byte written to the
register will inform the DS21352/552 which bits the user wishes to read and have cleared. The user will
write a byte to one of these registers, with a one in the bit positions he or she wishes to read and a zero in
the bit positions he or she does not wish to obtain the latest information on. When a one is written to a bit
location, the read register will be updated with the latest information. When a zero is written to a bit
position, the read register will not be updated and the previous value will be held. A write to the status
and information registers will be immediately followed by a read of the same register. The read result
should be logically AND’ed with the mask byte that was just written and this value should be written
back into the same register to insure that bit does indeed clear. This second write step is necessary
because the alarms and events in the status registers occur asynchronously in respect to their access via
the parallel port. This write–read– write scheme allows an external microcontroller or microprocessor to
individually poll certain bits without disturbing the other bits in the register. This operation is key in
controlling the DS21352/552 with higher–order software languages.
The SR1, SR2, and HSR registers have the unique ability to initiate a hardware interrupt via the INT
output pin. Each of the alarms and events in the SR1, SR2, and HSR can be either masked or unmasked
from the interrupt pin via the Interrupt Mask Register 1 (IMR1), Interrupt Mask Register 2 (IMR2), and
HDLC Interrupt Mask Register (HIMR) respectively. The HIMR register is covered in Section 15.3.2.
The interrupts caused by alarms in SR1 (namely RYEL, LRCL, RBL, and RLOS) act differently than the
interrupts caused by events in SR1 and SR2 (namely LUP, LDN, LOTC, RSLIP, RMF, TMF, SEC,
RFDL, TFDL, RMTCH, RAF, and RSC) and HIMR. The alarm caused interrupts will force the INT pin
low whenever the alarm changes state (i.e., the alarm goes active or inactive according to the set/clear
criteria in Table 7-2). The INT pin will be allowed to return high (if no other interrupts are present) when
the user reads the alarm bit that caused the interrupt to occur even if the alarm is still present. The event
caused interrupts will force the INT pin low when the event occurs. The INT pin will be allowed to return
high (if no other interrupts are present) when the user reads the event bit that caused the interrupt to
occur.
相關PDF資料
PDF描述
DS2156L+ IC TXRX T1/E1/J1 1-CHIP 100-LQFP
DS2155LC2+ IC TXRX T1/E1/J1 SGL 100-LQFP
DS26504L+ IC T1/E1/J1 64KCC ELEMENT 64LQFP
MC908QT2AMFQE IC MCU 8BIT 1.5K FLASH 8-DFN
MC9S08LG16CLH IC MCU 8BIT LG16 FLASH 64-LQFP
相關代理商/技術參數
參數描述
DS21352LN+ 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V/5V E1 Single-Chip Transceivers
DS21354DK 功能描述:網絡開發工具 DS21354 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS21354G 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354GN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*