- 您現在的位置：買賣IC網 > PDF目錄10993 > DS21552LN+ (Maxim Integrated Products)IC TXRX T1 1-CHIP 5V 100-LQFP PDF資料下載
參數資料
| 型號： | DS21552LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 76/137頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX T1 1-CHIP 5V 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 功能： | 單芯片收發器 |
| 接口： | E1，HDLC，J1，T1 |
| 電路數： | 1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 電流 - 電源： | 75mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
| 包括： | DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁
DS21352/DS21552
43 of 137
7. STATUS AND INFORMATION REGISTERS
There is a set of nine registers that contain information on the current real time status of the device, Status
Register 1 (SR1), Status Register 2 (SR2), Receive Information Registers 1 to 3 (RIR1/RIR2/RIR3) and a
set of four registers for the onboard HDLC and BOC controller. The specific details on the four registers
pertaining to the HDLC controller are covered in Section 15.3.2 but they operate the same as the other
status registers in the DS21352/552 and this operation is described below.
When a particular event has occurred (or is occurring), the appropriate bit in one of these nine registers
will be set to a one. All of the bits in SR1, SR2, RIR1, RIR2, and RIR3 registers operate in a latched
fashion. This means that if an event or an alarm occurs and a bit is set to a one in any of the registers, it
will remain set until the user reads that bit. The bit will be cleared when it is read and it will not be set
again until the event has occurred again (or in the case of the RBL, RYEL, LRCL, and RLOS alarms, the
bit will remain set if the alarm is still present). There are bits in the four HDLC status registers that are
not latched and these bits are listed in Section 15.3.2.
The user will always proceed a read of any of the nine registers with a write. The byte written to the
register will inform the DS21352/552 which bits the user wishes to read and have cleared. The user will
write a byte to one of these registers, with a one in the bit positions he or she wishes to read and a zero in
the bit positions he or she does not wish to obtain the latest information on. When a one is written to a bit
location, the read register will be updated with the latest information. When a zero is written to a bit
position, the read register will not be updated and the previous value will be held. A write to the status
and information registers will be immediately followed by a read of the same register. The read result
should be logically AND’ed with the mask byte that was just written and this value should be written
back into the same register to insure that bit does indeed clear. This second write step is necessary
because the alarms and events in the status registers occur asynchronously in respect to their access via
the parallel port. This write–read– write scheme allows an external microcontroller or microprocessor to
individually poll certain bits without disturbing the other bits in the register. This operation is key in
controlling the DS21352/552 with higher–order software languages.
The SR1, SR2, and HSR registers have the unique ability to initiate a hardware interrupt via the INT
output pin. Each of the alarms and events in the SR1, SR2, and HSR can be either masked or unmasked
from the interrupt pin via the Interrupt Mask Register 1 (IMR1), Interrupt Mask Register 2 (IMR2), and
HDLC Interrupt Mask Register (HIMR) respectively. The HIMR register is covered in Section 15.3.2.
The interrupts caused by alarms in SR1 (namely RYEL, LRCL, RBL, and RLOS) act differently than the
interrupts caused by events in SR1 and SR2 (namely LUP, LDN, LOTC, RSLIP, RMF, TMF, SEC,
RFDL, TFDL, RMTCH, RAF, and RSC) and HIMR. The alarm caused interrupts will force the INT pin
low whenever the alarm changes state (i.e., the alarm goes active or inactive according to the set/clear
criteria in Table 7-2). The INT pin will be allowed to return high (if no other interrupts are present) when
the user reads the alarm bit that caused the interrupt to occur even if the alarm is still present. The event
caused interrupts will force the INT pin low when the event occurs. The INT pin will be allowed to return
high (if no other interrupts are present) when the user reads the event bit that caused the interrupt to
occur.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2174Q+T&R | IC BERT ENHANCED 44-PLCC |
| DS2155G+T&R | IC TXRX T1/E1/J1 1 CHIP 100CSBGA |
| DS2155G+ | IC TXRX T1/E1/J1 1-CHIP 100CSBGA |
| DS2155G | IC TXRX T1/E1/J1 1-CHIP 100CSBGA |
| VE-B4Z-IX-B1 | CONVERTER MOD DC/DC 2V 30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21552LN+ | 功能描述:網絡控制器與處理器 IC 5V T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21554 | 制造商:Maxim Integrated Products 功能描述: |
| DS21554G | 功能描述:IC TXRX E1 1-CHIP 5V 100-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| DS21554GN | 功能描述:IC TXRX E1 1-CHIP 5V 100-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| DS21554L | 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。