參數資料
型號： DS2180A
英文描述： T1 Transceiver
中文描述： T1收發器
文件頁數： 22/35頁
文件大?。?/td> 481K
代理商： DS2180A
DS2180A
22 of 35
4.
RLOS transitions high during the F-bit time that caused an OOF event (any two of four consecutive
F
T
or FPS bits are in error) if auto-resync mode is selected (RCR.1=0). Resync will also occur when
loss of carrier is detected (RCL=1). When RCR.1=1, RLOS remains low until resync occurs,
regardless of OOF or carrier loss flags. In this situation, resync is initiated only when RCR.0
transitions low-to-high or the
RST
pin transitions high-low-high.
HARDWARE MODE
For preliminary system prototyping or applications which do not require the features offered by the serial
port, the transceiver can be reconfigured by the SPS pin. Tying SPS to V
SS
disables the serial port, clears
all internal registers except CCR and TCR and redefines pins 14 through 18 as mode control inputs. The
hardware mode allows device retrofit into existing applications where mode control and alarm
conditioning hardware is often designed with discrete logic.
HARDWARE COMMON CONTROL
In the hardware mode bits TCR.2, CCR.4, TCR.0, CCR.1 and CCR.2 map to pins 14 through 18. The
loop-back feature (bit CCR.0) is enabled by tying pins 17 (zero suppression) and 18 (B8ZS) to 1. (The
last states of pins 17 and 18 are latched as when both pins are taken high, preserving the current zero
suppression mode). Robbed bit signaling (bit TCR.4) is enabled for all channels. The user may tie TSER
to TABCD externally to disable signaling if so desired. Bit CCR.3 is forced to 0 which selects bit 2
yellow alarm in 193S framing. Contents of the RCR, as well as the remaining bit locations in the CCR
and TCR are cleared in the hardware mode. The
RST
input may be used to force immediate receiver
resync and has no effect on transmit.
HARDWARE MODE
Table 6
PIN
NUMBER
14 (16)
REGISTER BIT
LOCATION
TCR-D2
NAME AND DESCRIPTION
193S – S-bit insertion
3
1 = external; 0 = internal
Framing Mode Select.
1 = 193E; 0 = 193S
Transmit Yellow Alarm
2 ,3
1 = enabled; 0 = disabled
Zero Suppression
1
1 = bit 7 stuffing
0 = transparent
B8ZS
1
1 = enabled; 0 = disabled
15 (17)
CCR-D4
16 (18)
TCR-D0
17 (19)
CCR-D1
18 (20)
CCR-D2
NOTES
1.
Tying pins 17 and 18 high enables loopback in the hardware mode.
2.
Bit 2 (193S) and data link (193E) yellow alarms are supported.
3.
S-bit yellow alarm (193S) is not internally supported; however, the user may elect to insert external S
bits for alarm purposes.
4.
Pin numbers for PLCC package are listed in parenthesis.
相關PDF資料
PDF描述
DS21FT40 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
DS21FT42 Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
DS21Q50N Telecommunication IC
DS21Q55DK Quad T1/E1/J1 Transceiver Design Kit Daughter Card
DS21Q55 Quad T1/E1/J1 Transceiver
相關代理商/技術參數
參數描述
DS2180A+ 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AN 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2180AQ/T&R 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver
DS2180AQ/T&R+ 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*