- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2250-64-16+ (Maxim Integrated Products)IC MCU 64KB 16MHZ 40-SIMM PDF資料下載
參數資料
| 型號： | DS2250-64-16+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/18頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 64KB 16MHZ 40-SIMM |
| 標準包裝： | 1 |
| 系列： | DS225x |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器類型： | SRAM |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 振蕩器型： | 外部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 40-SIMM |
| 包裝： | 托盤 |
DS2250(T)
3 of 18
PIN DESCRIPTION
PIN
DESCRIPTION
1, 3, 5, 7, 9,
11, 13, 15
P1.0 - P1.7. General purpose I/O Port 1
17
RST - Active high reset input. A logic 1 applied to this pin will activate a reset state.
This pin is pulled down internally so this pin can be left unconnected if not used. An
RC power-on reset circuit is not needed and is not recommended.
19
P3.0 RXD. General purpose I/O port pin 3.0. Also serves as the receive signal for the
on board UART. This pin should not be connected directly to a PC COM port.
21
P3.1 TXD. General purpose I/O port pin 3.1. Also serves as the transmit signal for the
on board UART. This pin should not be connected directly to a PC COM port.
23
P3.2 INT0 . General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
25
P3.3 INT1 . General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
27
P3.4 T0. General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
29
P3.5 T1. General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
31
P3.6 WR . General purpose I/O port pin. Also serves as the write strobe for Expanded
bus operation.
33
P3.7 RD . General purpose I/O port pin. Also serves as the read strobe for Expanded
bus operation.
35, 37
XTAL2, XTAL1. Used to connect an external crystal to the internal oscillator.
XTAL1 is the input to an inverting amplifier and XTAL2 is the output.
39
GND - Logic ground.
26, 28, 30, 32,
34, 36, 38, 40
P2.7-P2.0. General purpose I/O Port 2. Also serves as the MSB of the Expanded
Address bus.
24
PSEN
- Program Store Enable. This active low signal is used to enable an external
program memory when using the Expanded bus. It is normally an output and should
be unconnected if not used. PSEN also is used to invoke the Bootstrap Loader. At this
time, PSEN will be pulled down externally. This should only be done once the
DS2250(T) is already in a reset state. The device that pulls down should be open-drain
since it must not interfere with PSEN under normal operation.
22
ALE - Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a
’373 type transparent latch. When using a parallel programmer, this pin also assumes
the PROG function for programming pulses.
20
EA
- External Access. This pin forces the DS2250(T) to behave like an 8031. No
internal memory (or clock) will be available when this pin is at a logic low. Since this
pin is pulled down internally, it should be connected to +5V to use NV RAM. In a
parallel programmer, this pin also serves as VPP for super voltage pulses.
4, 6, 8, 10, 12,
14, 16, 18
P0.0-P0.7. General purpose I/O Port 0. This port is open-drain and can not drive a
logic 1. It requires external pullups. Port 0 is also the multiplexed Expanded
Address/Data bus. When used in this mode, it does not require pullups.
2
VCC + - 5 volts.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2251T-128-16 | IC MICROCNTRLR 128K 16MHZ 72SIMM |
| DS2252T-128-16 | IC MICROCNTRLR 128K 16MHZ 40SIMM |
| DS2291/87-22291-000 | IC STIK T1 LONG LOOP 5V 30-SIP |
| DS229S/T&R | IC TXRX TRI 5V RS-232 IND 20SOIC |
| DS232AR | IC TXRX DUAL RS-232 5V 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2250-64-16# | 功能描述:模塊化系統 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2250-64-16+ | 功能描述:IC MCU 64KB 16MHZ 40-SIMM RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:DS225x 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS2250-64-8 | 功能描述:模塊化系統 - SOM RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2250-8-16 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Soft Microcontroller Module |
| DS2250-8-8 | 制造商:Maxim Integrated Products 功能描述:SIPSTIK, MICRO 8KX8 8MHZ - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。