參數資料
型號: DS2250-64-16+
廠商: Maxim Integrated Products
文件頁數: 15/18頁
文件大?。?/td> 0K
描述: IC MCU 64KB 16MHZ 40-SIMM
標準包裝: 1
系列: DS225x
核心處理器: 8051
芯體尺寸: 8-位
速度: 16MHz
連通性: SIO,UART/USART
外圍設備: 電源故障復位,WDT
輸入/輸出數: 32
程序存儲器類型: SRAM
RAM 容量: 64K x 8
電壓 - 電源 (Vcc/Vdd): 4.75 V ~ 5.25 V
振蕩器型: 外部
工作溫度: 0°C ~ 70°C
封裝/外殼: 40-SIMM
包裝: 托盤
DS2250(T)
6 of 18
SERIAL BOOTSTRAP LOADER
The Serial Program Load Mode is the easiest, fastest, most reliable, and most complete method of
initially loading application software into the DS2250(T) nonvolatile RAM. Communication can be
performed over a standard asynchronous serial communications port. A typical application would use a
simple RS232C serial interface to program the DS2250(T) as a final production procedure. The hardware
configuration which is required for the Serial Program Load Mode is illustrated in Figure 3. Port pins 2.7
and 2.6 must be either open or pulled high to avoid placing the device in a parallel load cycle. Although
an 11.0592 MHz crystal is shown in Figure 3, a variety of crystal frequencies and loader baud rates are
supported, shown in Table 2. The serial loader is designed to operate across a 3-wire interface from a
standard UART. The receive, transmit, and ground wires are all that are necessary to establish
communication with the DS2250(T).
The Serial Bootstrap Loader implements an easy-to-use command line interface which allows an
application program in an Intel hex representation to be loaded into and read back from the device. Intel
hex is the typical format which existing 8051 cross-assemblers output. The serial loader responds to
single character commands which are summarized below:
COMMAND
FUNCTION
C
Return CRC-16 checksum of embedded RAM
D
Dump Intel hex File
F
Fill embedded RAM block with constant
K
Load 40-bit encryption key
L
Load Intel hex file
R
Read MCON register
T
Trace (Echo) incoming Intel hex data
U
Clear Security Lock
V
Verify Embedded RAM with incoming Intel hex
W
Write MCON register
Z
Set security lock
P
Put a value to a port
G
Get a value from a port
Table 1 summarizes the selection of the available Parallel Program Load cycles. The timing associated
with these cycles is illustrated in the electrical specs.
PARALLEL PROGRAM LOAD CYCLES Table 1
MODE
RST
PSEN
PROG
EA
P2.7
P2.6
P2.5
Program
1
0
VPP
1
0
X
Security Set
1
0
VPP
1
X
Verify
1
X
1
0
X
Prog Expanded
1
0
VPP
0
1
0
Verify Expanded
1
0
1
0
1
0
Prog MCON or Key registers
1
0
VPP
0
1
Verify MCON registers
1
0
1
0
1
相關PDF資料
PDF描述
DS2251T-128-16 IC MICROCNTRLR 128K 16MHZ 72SIMM
DS2252T-128-16 IC MICROCNTRLR 128K 16MHZ 40SIMM
DS2291/87-22291-000 IC STIK T1 LONG LOOP 5V 30-SIP
DS229S/T&R IC TXRX TRI 5V RS-232 IND 20SOIC
DS232AR IC TXRX DUAL RS-232 5V 16-SOIC
相關代理商/技術參數
參數描述
DS2250-64-16# 功能描述:模塊化系統 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
DS2250-64-16+ 功能描述:IC MCU 64KB 16MHZ 40-SIMM RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:DS225x 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C,智能卡,UART/USART,USB 外圍設備:LED,POR,WDT 輸入/輸出數:9 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS2250-64-8 功能描述:模塊化系統 - SOM RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
DS2250-8-16 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Soft Microcontroller Module
DS2250-8-8 制造商:Maxim Integrated Products 功能描述:SIPSTIK, MICRO 8KX8 8MHZ - Rail/Tube