- 您現在的位置：買賣IC網 > PDF目錄4589 > DS2413P+ (Maxim Integrated Products)IC SWITCH DL ADDRESS 6-TSOC PDF資料下載
參數資料
| 型號： | DS2413P+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DL ADDRESS 6-TSOC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 120 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
DS2413: 1-Wire Dual Channel Addressable Switch
6 of 18
PIO STUCTURE
Each PIO consists of an open-drain pulldown transistor with 28V capability. The transistor is controlled by the PIO
Output Latch, as shown in Figure 5. The PIO Control unit connects the PIOs to the 1-Wire interface.
Figure 5. PIO Simplified Logic Diagram
PIO Pin
State
PIO Pin
PIO Out-
put Latch
PIO Output
Latch State.
Q
D
Q
PIO Data
PIO Clock
CLOCK
PIO FUNCTION COMMANDS
The PIO Function Flow Chart (Figure 6) describes the protocols necessary to access the PIO pins of the DS2413.
Examples on how to use these functions are included at the end of this document. The communication between
master and DS2413 takes place either at standard speed (default, OD = 0) or at Overdrive Speed (OD = 1). If not
explicitly set into the Overdrive Mode, the DS2413 powers up in standard speed.
PIO ACCESS READ [F5h]
This command reads the PIO logical status and reports it together with the state of the PIO Output Latch in an
endless loop. A PIO Access Read can be terminated at any time with a 1-Wire Reset.
PIO Status Bit Assignment
b7
b6
b5
b4
b3
b2
b1
b0
Complement of b3 to b0
PIOB Output
Latch State
PIOB Pin
State
PIOA Output
Latch State
PIOA Pin
State
The state of both PIO channels is sampled at the same time. The first sampling occurs during the last (most
significant) bit of the command code F5h. The PIO status is then reported to the bus master. While the master
receives the last (most significant) bit of the PIO status byte, the next sampling occurs and so on until the master
generates a 1-Wire Reset. The sampling occurs with a delay of tREH+x from the rising edge of the MS bit of the
previous byte, as shown in Figure 7. The value of "x" is approximately 0.2s.
Figure 7. PIO Access Read Timing Diagram
IO
MS 2 bits of
previous byte
LS 2 bits of PIO
Status byte
VTH
Sampling Point
tREH+x
Notes:
1
The "previous byte" could be the command code or the data byte resulting from the previous PIO sample.
2
The sample point timing also applies to the PIO Access Write command, with the "previous byte" being the
write confirmation byte (AAh).
相關PDF資料 |
PDF描述 |
|---|---|
| DS2401Z+ | IC SILICON SERIAL NUMBER SOT-223 |
| DS2401P+ | IC SILICON SERIAL NUMBER 6-TSOC |
| LFEC10E-3FN256C | IC FPGA 10.2KLUTS 195I/O 256-BGA |
| LFXP6E-3Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-4Q208C | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2413P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 制造商:Maxim Integrated Products 功能描述:IC, DUAL CHANNEL ADDRESSABLE SW, TSOC-6 |
| DS2413P+T&R | 制造商:Maxim Integrated Products 功能描述:ADDRESSABLE SWIT 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SWITCH DL ADDRESS 6TSOC 制造商:Maxim Integrated Products 功能描述:Interface - Specialized Dual Addressable Switch |
| DS2413P+T&R | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。