- 您現在的位置：買賣IC網 > PDF目錄4589 > DS2413P+ (Maxim Integrated Products)IC SWITCH DL ADDRESS 6-TSOC PDF資料下載
參數資料
| 型號： | DS2413P+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DL ADDRESS 6-TSOC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 120 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
DS2413: 1-Wire Dual Channel Addressable Switch
9 of 18
The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be
left in the idle state if the transaction is to resume. If this does not occur and the bus is left low for more than 16s
(Overdrive speed) or more than 120s (standard speed), one or more devices on the bus may be reset.
Figure 9. Hardware Configuration
Open Drain
Port Pin
RX = RECEIVE
TX = TRANSMIT
100
MOSFET
RX
TX
RX
DATA
RPUP
IL
BUS MASTER
DS2413 1-Wire PORT
TRANSACTION SEQUENCE
The protocol for accessing the DS2413 through the 1-Wire port is as follows:
Initialization
ROM Function Command
PIO Function Command
Data
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence consists of a
reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the slave(s). The presence
pulse lets the bus master know that the DS2413 is on the bus and is ready to operate. For more details, see the 1-
Wire Signaling section.
1-Wire ROM FUNCTION COMMANDS
Once the bus master has detected a presence, it can issue one of the seven ROM function commands that the
DS2413 supports. All ROM function commands are 8 bits long. A list of these commands follows (refer to the flow
chart in Figure 10).
READ ROM [33h]
This command allows the bus master to read the DS2413’s 8-bit family code, unique 48-bit serial number, and 8-bit
CRC. This command can only be used if there is a single slave on the bus. If more than one slave is present on the
bus, a data collision occurs when all slaves try to transmit at the same time (open drain produces a wired-AND
result). The resultant family code and 48-bit serial number result in a mismatch of the CRC.
MATCH ROM [55h]
The Match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a specific
DS2413 on a multidrop bus. Only the DS2413 that exactly matches the 64-bit ROM sequence, including the
external address, responds to the following PIO Function command. All other slaves wait for a reset pulse. This
command can be used with a single or multiple devices on the bus.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2401Z+ | IC SILICON SERIAL NUMBER SOT-223 |
| DS2401P+ | IC SILICON SERIAL NUMBER 6-TSOC |
| LFEC10E-3FN256C | IC FPGA 10.2KLUTS 195I/O 256-BGA |
| LFXP6E-3Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-4Q208C | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2413P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 制造商:Maxim Integrated Products 功能描述:IC, DUAL CHANNEL ADDRESSABLE SW, TSOC-6 |
| DS2413P+T&R | 制造商:Maxim Integrated Products 功能描述:ADDRESSABLE SWIT 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SWITCH DL ADDRESS 6TSOC 制造商:Maxim Integrated Products 功能描述:Interface - Specialized Dual Addressable Switch |
| DS2413P+T&R | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。