- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2490Y (Maxim Integrated Products)IC BRIDGE CLIP USB TO 1-W 24SOIC PDF資料下載
參數資料
| 型號： | DS2490Y |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/50頁 |
| 文件大小： | 0K |
| 描述： | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| 標準包裝： | 1,000 |
| 應用： | USB |
| 接口： | 1 線 |
| 電源電壓： | 3 V ~ 5.5 V |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC W |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS2490
24 of 50
the FIFO content status must be monitored by host SW so that additional data can be sent to the FIFO
when necessary.
A similar EP3 FIFO content monitoring requirement exists for the block read. During a block read the
number of bytes loaded into the EP3 FIFO must be monitored so that the data can be read before the
FIFO overflows.
Command parameters:
1 byte specifying preamble size.
EP2 data:
Length
Description
Same as
preamble size
Preamble data to be written to the 1-Wire device.
EP3 data:
Length
Description
If R = 1 and preamble
size
4:
As specified in
the second byte
of the
preamble
Data read from the 1-Wire device.
If R = 0: None
No data is returned (this is a write application).
Result Register:
Code
Condition
CRC, CMP
ICP = 0, NTF = 0 or 1: Bad CRC or the release
sequence was not accepted.
0x00
ICP = 0, NTF = 1: no error detected
None
ICP = 0, NTF = 0: no error detected
None
ICP = 1
SET PATH—This command is used to activate a series of couplers that finally provide the access to the
target 1-Wire device. Embedded command bit RST enables a 1-Wire reset before the command executes.
Additionally, embedded command bit F can be used to clear the communication command buffer and
EP2/3 FIFOs if an error occurs during execution of the command. The EP2 FIFO must be pre-filled with
coupler data before command execution. Additionally, for coupler data sizes greater then the EP2 FIFO
size, the FIFO content status must be monitored by host SW so that additional data can be sent to the
FIFO when necessary. Upon completion of command execution, the EP3 FIFO is loaded with a 1-byte
value that indicates the number of couplers activated. An NRS error code is an indication that there was
no presence pulse on the branch that was to be connected.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| DS26324GNA2+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26401N+ | IC OCTAL FRAMER T1/E1/J1 256-BGA |
| DS26504LNB2+ | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2490Y+ | 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Tape and Reel |
| DS24B33 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 4Kb EEPROM |
| DS24B33 R | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 4Kb EEPROM |
| DS24B33 T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 4Kb EEPROM |
| DS24B33 TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 4Kb EEPROM |
發布緊急采購，3分鐘左右您將得到回復。