- 您現在的位置：買賣IC網 > PDF目錄1915 > DS26324GNA2+ (Maxim Integrated Products)IC INTERFACE LINE 16CH 256-CSBGA PDF資料下載
參數資料
| 型號： | DS26324GNA2+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 113/120頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE LINE 16CH 256-CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 16/16 |
| 規程： | LIN |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 256-LBGA，CSBGA |
| 供應商設備封裝： | 256-CSBGA（17x17） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁當前第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
DS26324 3.3V, 16-Channel, E1/T1/J1 Short-Haul Line Interface Unit
92 of 120
7.1
TAP Controller State Machine
The TAP controller is a finite state machine that responds to the logic level at TMS on the rising edge of TCLK. The
state diagram is shown in Figure 7-2.
7.1.1
Test-Logic-Reset
Upon power-up, the TAP controller will be in the Test-Logic-Reset state. The instruction register will contain the
IDCODE instruction. All system logic of the device will operate normally. This state is automatically entered during
power-up. This state is entered from any state if the TMS is held high for at least 5 clocks.
7.1.2
Run-Test-Idle
The Run-Test-Idle is used between scan operations or during specific tests. The instruction register and test
registers will remain idle. The controller remains in this state when TMS is held low. When the TMS is high and
rising edge of TCLK is applied the controller moves to the Select-DR-Scan state.
7.1.3
Select-DR-Scan
All test registers retain their previous state. With TMS LOW, a rising edge of TCLK moves the controller into the
Capture-DR state and will initiate a scan sequence. TMS HIGH during a rising edge on TCLK moves the controller
to the Select-IR-Scan state.
7.1.4
Capture-DR
Data can be parallel-loaded into the test-data registers if the current instruction is EXTEST or SAMPLE/PRELOAD.
If the instruction does not call for a parallel load or the selected register does not allow parallel loads, the test
register will remain at its current value. On the rising edge of TCLK, the controller will go to the shift-DR state if
TMS is LOW or it will go to the exit1-DR state if TMS is HIGH.
7.1.5
Shift-DR
The test-data register selected by the current instruction will be connected between TDI and TDO and will shift data
one stage towards its serial output on each rising edge of TCLK. If a test register selected by the current instruction
is not placed in the serial path, it will maintain its previous state. When the TAP controller is in this state and a
rising edge of TCLK is applied, the controller enters the Exit1-DR state if TMS is high or remains in Shift-DR state if
TMS is low.
7.1.6
Exit1-DR
While in this state, a rising edge on TCLK will put the controller in the Update-DR state, which terminates the
scanning process, if TMS is HIGH. A rising edge on TCLK with TMS LOW will put the controller in the Pause-DR
state.
7.1.7
Pause-DR
Shifting of the test registers is halted while in this state. All test registers selected by the current instruction will
retain their previous state. The controller will remain in this state while TMS is LOW. A rising edge on TCLK with
TMS HIGH will put the controller in the Exit2-DR state.
7.1.8
Exit2-DR
A rising edge on TCLK with TMS HIGH while in this state will put the controller in the Update-DR state and
terminate the scanning process. A rising edge on TCLK with TMS LOW will enter the Shift-DR state.
7.1.9
Update-DR
A falling edge on TCLK while in the Update-DR state will latch the data from the shift register path of the test
registers into the data output latches. This prevents changes at the parallel output due to changes in the shift
register.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26401N+ | IC OCTAL FRAMER T1/E1/J1 256-BGA |
| DS26504LNB2+ | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
| DS26514G+ | IC TXRX T1/E1/J1 4PORT 256-CSBGA |
| DS26518NB1+ | IC TXRX T1/E1/J1 8PORT 256-CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26324GNA2+ | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA2+W | 制造商:Maxim Integrated Products 功能描述:FRAMER E1/J1/T1 3.3V 256PIN TE-CSBGA - Rail/Tube |
| DS26324GNA3 | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA3+ | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324N | 制造商:Maxim Integrated Products 功能描述:DS26324 X16 T1E1J1 LIU S-HAUL IND - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。