- 您現在的位置：買賣IC網 > PDF目錄1915 > DS26324GNA2+ (Maxim Integrated Products)IC INTERFACE LINE 16CH 256-CSBGA PDF資料下載
參數資料
| 型號： | DS26324GNA2+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 27/120頁 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE LINE 16CH 256-CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 16/16 |
| 規程： | LIN |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 256-LBGA，CSBGA |
| 供應商設備封裝： | 256-CSBGA（17x17） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
DS26324 3.3V, 16-Channel, E1/T1/J1 Short-Haul Line Interface Unit
14 of 120
NAME
PIN
TYPE
FUNCTION
SCLK/ALE/ASB
N14
I
Shift Clock. In the serial host mode, this pin is the serial clock. Data
on SDI is clocked on the rising edge of SCLK. The data is clocked on
SDO on the rising edge of SCLK if CLKE is high. If CLKE is low the
data on SDO is clocked on the falling edge of SCLK.
Address Latch Enable. In parallel Intel multiplexed mode, the
address lines are latched on the falling edge of ALE.
Address Strobe Bar. In parallel Motorola multiplexed mode, the
address is sampled on the falling edge of ASB.
Note: Tie ALE/ASB pin high if using nonmuxed mode.
RDB/RWB
H14
I
Read Bar. In Intel host mode, this pin must be low for read operation.
Read Write Bar. In Motorola mode, this pin is low for write operation
and high for read operation.
SDI/WRB/DSB
G14
I
Serial Data Input. In the serial host mode, this pin is the serial input
SDI; it is sampled on the rising edge of SCLK.
Write Bar. In Intel host mode, this pin is active low during write
operation. The data or address (multiplexed mode) is sampled on the
rising edge of WRB.
Data Strobe Bar. In the parallel Motorola mode, this pin is active low.
During a write operation the data or address is sampled on the rising
edge of DSB. During a read operation the data or address is driven
on the rising edge of DSB. In the nonmultiplexed Motorola mode the
address bus (A[5:0]) is latched on the falling edge of DSB.
SD0/RDYB/ACKB
C13
O
Serial Data Out. In serial host mode, the SDO data is output on this
pin. If a serial write is in progress this pin is high impedance. During a
read SDO is high impedance when the SDI is in command/address
mode. If CLKE is low SDO is output on the rising edge of SCLK, if
CLKE is high on the falling edge.
Ready Bar Output. A high on this pin reports to the host that the
cycle is not complete and wait states must be inserted. A low means
the cycle is complete.
Acknowledge Bar. In Motorola parallel mode, a low on this pin
indicates that the read data is available for the Host or that the written
data cycle is complete.
INTB
D7
O,
open
drain
Interrupt Bar (Active Low). This signal is tri-state when RSTB pin is
low. This interrupt signal is driven low when an event is detected on
any of the enabled interrupt sources in any of the register banks.
When there are no active and enabled interrupt sources, the pin can
be programmed to either drive high or as open drain. The reset
default is open drain when there are no active enabled interrupt
sources. All interrupt sources are disabled when RSTB = 0 and they
must be programmed to be enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26401N+ | IC OCTAL FRAMER T1/E1/J1 256-BGA |
| DS26504LNB2+ | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
| DS26514G+ | IC TXRX T1/E1/J1 4PORT 256-CSBGA |
| DS26518NB1+ | IC TXRX T1/E1/J1 8PORT 256-CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26324GNA2+ | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA2+W | 制造商:Maxim Integrated Products 功能描述:FRAMER E1/J1/T1 3.3V 256PIN TE-CSBGA - Rail/Tube |
| DS26324GNA3 | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324GNA3+ | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26324N | 制造商:Maxim Integrated Products 功能描述:DS26324 X16 T1E1J1 LIU S-HAUL IND - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。