- 您現在的位置：買賣IC網 > PDF目錄9671 > DS26502L+ (Maxim Integrated Products)IC T1/E1/J1 64KCC ELEMENT 64LQFP PDF資料下載
參數資料
| 型號： | DS26502L+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 109/125頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC T1/E1/J1 64KCC ELEMENT 64LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 160 |
| 類型： | BITS 元件，多路復用器 |
| PLL： | 是 |
| 主要目的： | T1/E1 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:3 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 6.312MHz |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1430 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁當前第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
DS26502 T1/E1/J1/64KCC BITS Element
84 of 125
Register Name:
LIC2
Register Description:
Line Interface Control 2
Register Address:
31h
Bit #
7
6
5
4
3
2
1
0
Name
JACKS1
LIRST
IBPV
TAIS
JACKS0
RCCFE
SCLD
CLDS
Default
0
HW
Mode
0
TAIS
PIN 10
JACKS
PIN 46
0
Bit 0: Custom Line Driver Select (CLDS). Setting this bit to a one will redefine the operation of the transmit line driver.
When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7 = 0, then the device will generate a square wave at the TTIP and
TRING outputs instead of a normal waveform. When this bit is set to a one and LIC1.5 = LIC1.6 = LIC1.7
≠ 0, then the device
will force TTIP and TRING outputs to become open-drain drivers instead of their normal push-pull operation. This bit should
be set to zero for normal operation of the device. Note: This bit should be set = 0 in 64KCC and 6312kHz transmit modes.
Bit 1: Short Circuit Limit Disable (in E1 mode) (SCLD). Controls the 50mA (rms) current limiter. Note: Not applicable in
6312kHz mode.
0 = enable 50mA current limiter
1 = disable 50mA current limiter
Bit 2: Receive Composite Clock Filter Enable (RCCFE). (64KCC mode only) Setting this bit will enable the PLL filter on
the received 64kHz composite clock. Note: the 8kHz and 400Hz output are not filtered.
0 = Receive Composite Clock Filter Disabled
1 = Receive Composite Clock Filter Enabled
Bit 3: Jitter Attenuator Clock Select 0 (JACKS0). This bit, along with JACKS1 (LIC2.7), MPS0 (LIC4.6), and MPS1
(LIC4.7), controls the source for JA CLOCK from the MCLK pin. Note: This bit must be configured even if the jitter
attenuator is disabled. The clock and data recovery engine also uses the JA CLOCK. Setting this bit enables the 2.048MHz to
1.544MHz conversion PLL for T1 applications. See the table in the LIC4 register description for more details on setting up the
JA CLOCK source.
0 = 2.048MHz to 1.544MHz PLL bypassed
1 = 2.048MHz to 1.544MHz PLL enabled
Bit 4: Transmit Alarm Indication Signal (TAIS)
0 = transmit an unframed all-ones code
1 = transmit data normally
Bit 5: Insert BPV (IBPV). A zero-to-one transition on this bit will cause a single BPV to be inserted into the transmit data
stream. Once this bit has been toggled from a zero to a one, the device waits for the next occurrence of three consecutive ones
to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted. Note: This function not
supported in 64KCC and 6312kHz modes.
Bit 6: Line Interface Reset (LIRST). Setting this bit from a zero to a one will initiate an internal reset that resets the clock
recovery state machine and recenters the jitter attenuator. Normally this bit is only toggled on power-up. Must be cleared and
set again for a subsequent reset.
Bit 7: Jitter Attenuator Clock Select 1 (JACKS1). This bit, along with JACKS0 (LIC2.3), MPS0 (LIC4.6), and MPS1
(LIC4.7), controls the source for JA CLOCK from the MCLK pin. Note: This bit must be configured even if the jitter
attenuator is disabled. The clock and data recovery engine also uses the JA CLOCK. Setting this bit enables the 12.8MHz to
2.048MHz conversion PLL. See the table in the LIC4 register description for more details on setting up the JA CLOCK source.
0 = 12.8MHz to 2.048MHz PLL bypassed
1 = 12.8MHz to 2.048MHz PLL enabled
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20ME26JN | CONN RCPT 26POS WALL MNT W/SCKT |
| MAX3634ETM+ | IC CLOCK PHASE ALIGNER 48-TQFN |
| VE-B4W-MW-F1 | CONVERTER MOD DC/DC 5.5V 100W |
| VE-B4V-MW-F3 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B4V-MW-F2 | CONVERTER MOD DC/DC 5.8V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26502L+ | 功能描述:計時器和支持產品 E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS26502LB1 | 功能描述:計時器和支持產品 E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS26502LN | 功能描述:計時器和支持產品 E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS26502LN+ | 功能描述:計時器和支持產品 E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| DS26503 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:T1/E1/J1/64KCC BITS Element |
發布緊急采購，3分鐘左右您將得到回復。