- 您現在的位置：買賣IC網 > PDF目錄376970 > DS2761 High-Precision Li+ Battery Monitor PDF資料下載
參數資料
| 型號： | DS2761 |
| 英文描述： | High-Precision Li+ Battery Monitor |
| 中文描述： | 高精度、Li+電池監視器 |
| 文件頁數： | 13/24頁 |
| 文件大小： | 286K |
| 代理商： | DS2761 |
DS2761
13 of 24
Figure 10.
STATUS REGISTER FORMAT
Address 01
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
X
X
PMOD
RNAOP
SWEN
X
X
X
PMOD—
Sleep Mode Enable. A value of 1 in this bit enables the DS2761 to enter sleep mode when the
DQ line goes low for greater than 2s and to leave sleep mode when the DQ line goes high. A value of 0
disables DQ-related transitions into and out of sleep mode. This bit is read-only. The desired default value
should be set in bit 5 of address 31h. The factory default is 0.
RNAOP
—Read Net Address Opcode. A value of 0 in this bit sets the opcode for the read net address
command to 33h, while a 1 sets the opcode to 39h. This bit is read-only. The desired default value should
be set in bit 4 of address 31h. The factory default is 0.
SWEN—
SWAP Command Enable. A value of 1 in this bit location enables the recognition of a SWAP
command. If set to 0, SWAP commands are ignored. The desired default value should be set in bit 3 of
address 31h. This bit is read-only. The factory default is 0.
X
—Reserved Bits.
EEPROM REGISTER
The format of the EEPROM register is shown in Figure 11. The function of each bit is described in detail
in the following paragraphs.
Figure 11.
EEPROM REGISTER FORMAT
Address 07
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EEC
LOCK
X
X
X
X
BL1
BL0
EEC
—EEPROM Copy Flag. A 1 in this read-only bit indicates that a copy data command is in progress.
While this bit is high, writes to EEPROM addresses are ignored. A 0 in this bit indicates that data may be
written to unlocked EEPROM blocks.
LOCK
—EEPROM Lock Enable. When this bit is 0, the lock command is ignored. Writing a 1 to this bit
enables the lock command. After the lock command is executed, the LOCK bit is reset to 0. The factory
default is 0.
BL1—
EEPROM Block 1 Lock Flag. A 1 in this read-only bit indicates that EEPROM block 1 (addresses
30 to 3F) is locked (read-only) while a 0 indicates block 1 is unlocked (read/write).
BL0—
EEPROM Block 0 Lock Flag. A 1 in this read-only bit indicates that EEPROM block 0 (addresses
20 to 2F) is locked (read-only) while a 0 indicates block 0 is unlocked (read/write).
X
—Reserved Bits.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2761AE | High-Precision Li+ Battery Monitor |
| DS2761AX | High-Precision Li+ Battery Monitor |
| DS2761BE | High-Precision Li+ Battery Monitor |
| DS2761BX-025 | High-Precision Li+ Battery Monitor |
| DS276S | Low Power Transceiver Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2761AE | 功能描述:IC MON BATT LI-ION HP 16-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| DS2761AE+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2761AE+025 | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2761AE+025/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC MON BATT LI-ION HP 16-TSSOP |
| DS2761AE+025/T&R | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。