參數資料
型號： DS3234S#
廠商： Maxim Integrated Products
文件頁數： 6/21頁
文件大?。?/td> 0K
描述： IC RTC W/TCXO 20-SOIC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 45
類型： 時鐘/日歷
特點： 警報器，閏年，NVSRAM，方波輸出，TCXO/晶體
存儲容量： 256B
時間格式： HH:MM:SS（12/24 小時）
數據格式： YY-MM-DD-dd
接口： SPI
電源電壓： 2 V ~ 5.5 V
電壓 - 電源，電池： 2 V ~ 3.8 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 20-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 20-SOIC W
包裝： 管件
產品目錄頁面： 1434 (CN2011-ZH PDF)
DS3234
Extremely Accurate SPI Bus RTC with
Integrated Crystal and SRAM
14
____________________________________________________________________
Special-Purpose Registers
The DS3234 has two additional registers (control and
control/status) that control the real-time clock, alarms,
and square-wave output.
Control Register (0Eh/8Eh)
Bit 7: Enable Oscillator (EOSC). When set to logic 0,
the oscillator is started. When set to logic 1, the oscilla-
tor is stopped when the DS3234 switches to battery
power. This bit is clear (logic 0) when power is first
applied. When the DS3234 is powered by VCC, the
oscillator is always on regardless of the status of the
EOSC bit. When EOSC is disabled, all register data is
static.
Bit 6: Battery-Backed Square-Wave Enable
(BBSQW). When set to logic 1 with INTCN = 0 and VCC
< VPF, this bit enables the square wave. When BBSQW
is logic 0, the INT/SQW pin goes high impedance when
VCC < VPF. This bit is disabled (logic 0) when power is
first applied.
Bit 5: Convert Temperature (CONV). Setting this bit to
1 forces the temperature sensor to convert the temper-
ature into digital code and execute the TCXO algorithm
to update the capacitance array to the oscillator. This
can only happen when a conversion is not already in
progress. The user should check the status bit BSY
before forcing the controller to start a new TCXO exe-
cution. A user-initiated temperature conversion does
not affect the internal 64-second (default interval)
update cycle. This bit is disabled (logic 0) when power
is first applied.
A user-initiated temperature conversion does not affect
the BSY bit for approximately 2ms. The CONV bit
remains at a 1 from the time it is written until the conver-
sion is finished, at which time both CONV and BSY go
to 0. The CONV bit should be used when monitoring
the status of a user-initiated conversion.
Bits 4 and 3: Rate Select (RS2 and RS1). These bits
control the frequency of the square-wave output when
the square wave has been enabled. The following table
shows the square-wave frequencies that can be select-
ed with the RS bits. These bits are both set to logic 1
(8.192kHz) when power is first applied.
Bit 2: Interrupt Control (INTCN). This bit controls the
INT/SQW signal. When the INTCN bit is set to logic 0, a
square wave is output on the INT/SQW pin. When the
INTCN bit is set to logic 1, a match between the time-
keeping registers and either of the alarm registers acti-
vates the INT/SQW (if the alarm is also enabled). The
corresponding alarm flag is always set regardless of
the state of the INTCN bit. The INTCN bit is set to logic
1 when power is first applied.
Bit 1: Alarm 2 Interrupt Enable (A2IE). When set to
logic 1, this bit permits the alarm 2 flag (A2F) bit in the
status register to assert INT/SQW (when INTCN = 1).
When the A2IE bit is set to logic 0 or INTCN is set to
logic 0, the A2F bit does not initiate an interrupt signal.
The A2IE bit is disabled (logic 0) when power is first
applied.
Bit 0: Alarm 1 Interrupt Enable (A1IE). When set to
logic 1, this bit permits the alarm 1 flag (A1F) bit in the
status register to assert INT/SQW (when INTCN = 1).
When the A1IE bit is set to logic 0 or INTCN is set to
logic 0, the A1F bit does not initiate the INT/SQW sig-
nal. The A1IE bit is disabled (logic 0) when power is
first applied.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
NAME:
EOSC
BBSQW
CONV
RS2
RS1
INTCN
A2IE
A1IE
POR*:
000
111
0
RS2
RS1
SQUARE-WAVE OUTPUT
FREQUENCY
0
1Hz
0
1
1.024kHz
1
0
4.096kHz
1
8.192kHz
SQUARE-WAVE OUTPUT FREQUENCY
Control Register (0Eh/8Eh)
*
POR is defined as the first application of power to the device, either VBAT or VCC.
相關PDF資料
PDF描述
DS32C35-33#T&R IC RTC ACCURATE I2C 3.3V 20-SOIC
DS3911T+ IC DAC 10BIT I2C QUAD 14TDFN
DS4000KI/WBGA IC OSC TCXO 19.44MHZ 24-BGA
DS4026S+WCN IC OSC TCXO 25MHZ 16-SOIC
DS4100HW+ IC OSC CLOCK 100MHZ 10LCCC
相關代理商/技術參數
參數描述
DS3234S# 功能描述:實時時鐘 Integrated RTC/TCXO/Crystal RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS3234S# 制造商:Maxim Integrated Products 功能描述:RTC TCXO CRYSTAL 3.3V 20SOIC 制造商:Maxim Integrated Products 功能描述:RTC, TCXO, CRYSTAL, 3.3V, 20SOIC 制造商:Maxim Integrated Products 功能描述:RTC, TCXO, CRYSTAL, 3.3V, 20SOIC; Date Format:DD:MM:YYYY; Clock Format:HH:MM:SS; Clock IC Type:RTC; Supply Voltage Min:2V; Supply Voltage Max:5.5V; Digital IC Case Style:SOIC; No. of Pins:20; Interface Type:SPI; Operating Temperature;RoHS Compliant: Yes
DS3234S#T&R 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 256BYTE 20SOIC W - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RTC W/TCXO 20-SOIC
DS3234S#T&R 功能描述:實時時鐘 Integrated RTC/TCXO/Crystal RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS3234S+ 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*