- 您現在的位置：買賣IC網 > PDF目錄1916 > DS3903E-020/T&R (Maxim Integrated Products)IC POT NV TRIPLE 128POS 20-TSSOP PDF資料下載
參數資料
| 型號： | DS3903E-020/T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT NV TRIPLE 128POS 20-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接片： | 128 |
| 電阻（歐姆）： | 10k，10k，90k |
| 電路數： | 3 |
| 溫度系數： | 標準值 ±300 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
Detailed Description
The DS3903 contains three NV, low-temperature coeffi-
cient digital potentiometers. It is accessible through a
2-wire bus, and it serves as a small, low-cost replace-
ment for designs using mechanical potentiometers. The
low end-to-end resistance temperature coefficient is
especially beneficial for designs using a digital poten-
tiometer as a 2-terminal variable resistor.
It operates in both 3V and 5V systems, and it features a
write-protect pin that can lock the positions of the
potentiometers. The address pin allows two DS3903s to
be placed on the same 2-wire bus.
With its low cost and small board space, the DS3903 is
well tailored to replace larger mechanical potentiome-
ters. This allows the automation of calibration in many
instances because the 2-wire interface can easily be
adjusted by test hardware. Once the system is calibrat-
ed, the write-protect pin can be disconnected and the
potentiometers retain their settings.
Potentiometer Memory
Organization
The potentiometers of the DS3903 are addressed by
communicating with the registers in Table 1.
Device Operation
Clock and Data Transitions
The SDA pin is normally pulled high with an external
resistor or device. Data on the SDA pin can only change
during SCL low time periods. Data changes during SCL
high periods indicates a start or stop condition depend-
ing on the conditions discussed below. See the timing
diagrams for further details (Figures 2 and 3).
Start Condition
A high-to-low transition of SDA with SCL high is a start
condition, which must precede any other command. See
the timing diagrams for further details (Figures 2 and 3).
Stop Condition
A low-to-high transition of SDA with SCL high is a stop
condition. After a read sequence, the stop command
places the DS3903 into a low-power mode. See the tim-
ing diagrams for further details (Figures 2 and 3).
Acknowledge
All address and data bytes are transmitted through a
serial protocol. The DS3903 pulls the SDA line low dur-
ing the ninth clock pulse to acknowledge that it has
received each word.
Standby Mode
The DS3903 features a low-power mode that is auto-
matically enabled after power-on, after a stop com-
mand, and after the completion of all internal
operations.
Memory Reset
After any interruption in protocol, power loss, or system
reset, the following steps reset the DS3903:
1)
Clock up to nine cycles.
2)
Look for SDA high in each cycle while SCL is high.
3)
Create a start condition while SDA is high.
Device Addressing
The DS3903 must receive an 8-bit device address word
following a start condition to enable a specific device
for a read or write operation. The address word is
clocked into the DS3903 MSB to LSB. The address
DS3903
Triple 128-Position Nonvolatile
Digital Potentiometer
_____________________________________________________________________
7
POTENTIOMETER 2
10k
ADDDR FAh
POTENTIOMETER 2
ADDDR FAh
2-WIRE
INTERFACE
EEPROM
DATA
RWP
WP
GND
SCL
SDA
A0
VCC
H2
W2
L2
POTENTIOMETER 0
10k
ADDDR F9h
POTENTIOMETER 0
ADDDR F9h
POTENTIOMETER 1
90k
ADDDR F8h
POTENTIOMETER 1
ADDDR F8h
H0
W0
L0
H1
W1
L1
DS3903
Figure 1. DS3903 Block Diagram
ADDRESS
POTENTIOMETER
END-TO-END RESISTANCE
NUMBER OF POSITIONS
F8h
Pot 1
90k
*128 (00h to 7Fh)
F9h
Pot 0
10k
*128 (00h to 7Fh)
FAh
Pot 2
10k
*128 (00h to 7Fh)
Table 1. Potentiometer Registers
*The most significant bit of each potentiometer position value is ignored. Writing a value greater than 7Fh to any of the potentiometer
registers results in a valid 7-bit position, without regard to the value of the most significant bit. Example: position 0x82 is the same as
position 0x02.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3905U-020 | IC POT NV TRIPLE 128POS 10-USOP |
| DS3906U+T&R | IC RESIST VAR TRPL 10USOP |
| DS3908N+T&R | IC POT DUAL DIGITAL 14-TDFN |
| DS3930E | IC POT NV HEX I/O MEM 20-TSSOP |
| DS4301Z-200 | IC POT DIG NV 200K 32POS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3904 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Triple 128-Position Nonvolatile Digital Variable Resistor/Switch |
| DS3904U-010 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Triple 128-Position Nonvolatile Digital |
| DS3904U-010+ | 功能描述:數字電位計 IC Triple 128-Position Nonvolatile RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3904U-010+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 128POS 10KOHM/20KOHM TRIPLE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT NV TRIPLE 128POS 8-USOP |
發布緊急采購，3分鐘左右您將得到回復。