- 您現在的位置：買賣IC網 > PDF目錄17033 > DS5000T/KIT (Maxim Integrated Products)KIT IC EVALUATION MPU/RTC PDF資料下載
參數資料
| 型號： | DS5000T/KIT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT IC EVALUATION MPU/RTC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 類型： | 微控制器 |
| 適用于相關產品： | DS5000 |
| 所含物品： | 演示板和軟件 |
DS5000(T)
6 of 19
PROGRAM LOADING CONFIGURATIONS Figure 3
Table 1 summarizes the selection of the available Parallel Program Load cycles. The timing associated
with these cycles is illustrated in the electrical specs.
SERIAL BOOTSTRAP LOADER
The Serial Program Load Mode is the easiest, fastest, most reliable, and most complete method of
initially loading application software into the DS5000(T) nonvolatile RAM. Communication can be
performed over a standard asynchronous serial communications port. A typical application would use a
simple RS232C serial interface to program the DS5000(T) as a final production procedure. The hardware
configuration required for the Serial Program Load mode is illustrated in Figure 3. Port pins 2.7 and 2.6
must be either open or pulled high to avoid placing the DS5000(T) in a parallel load cycle. Although an
11.0592 MHz crystal is shown in Figure 3, a variety of crystal frequencies and loader baud rates are
supported, shown in Table 2. The serial loader is designed to operate across a 3-wire interface from a
standard UART. The receive, transmit, and ground wires are all that are necessary to establish
communication with the DS5000(T).
The Serial Bootstrap Loader implements an easy-to-use command line interface that allows an application
program in an Intel hex representation to be loaded into and read back from the device. Intel hex is the
typical format which existing 8051 cross-assemblers output. The serial loader responds to single
character commands, which are summarized below:
相關PDF資料 |
PDF描述 |
|---|---|
| AFS-EVAL-KIT | KIT STARTER EVAL FUSION AFS600 |
| ESM10DRYS | CONN EDGECARD 20POS DIP .156 SLD |
| EMM11DRTN | CONN EDGECARD 22POS DIP .156 SLD |
| AGL-ICICLE-KIT | KIT EVAL FOR IGOO ICICLE |
| ECM25DCCN | CONN EDGECARD 50POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS5001FP | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
| DS5001FP08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| DS5001FP-12 | 功能描述:微處理器 - MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| DS5001FP-12-44 | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 80MQFP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。