參數資料
型號： DS80C390-QCR
元件分類： 微處理器
英文描述： Dual CAN High-Speed Microprocessor
中文描述： 雙CAN高速微處理器
文件頁數： 20/58頁
文件大小： 5486K
代理商： DS80C390-QCR
DS80C390
20 of 58
110199
Software should not rely on a lower-priority level interrupt source to remove PMM (Switchback) when a
higher level is in service. Check the current priority service level before entering PMM. If the current
service level locks out a desired Switchback source, then it would be advisable to wait until this condition
clears before entering PMM. Alternately, software can prevent an undesired exit from PMM by
intentionally entering a low priority interrupt service level before entering PMM. This will prevent other
low priority interrupts from causing a Switchback.
Entering PMM during an ongoing serial port transmission or reception can corrupt the serial port activity.
To prevent this, a hardware lockout feature ignores changes to the clock divisor bits while the serial ports
are active. Serial port activity can be monitored via the Serial Port Activity bits located in the Status
register.
IDLE MODE
Setting the IDLE bit (PCON.0) invokes the Idle mode. Idle will leave internal clocks, serial ports and
timers running. Power consumption drops because memory is not being accessed and instructions are not
being executed. Since clocks are running, the Idle power consumption is a function of crystal frequency.
It should be approximately of the operational power at a given frequency. The CPU can exit Idle mode
with any interrupt or a reset. Because Power Management Mode (PMM) consumes less power than Idle
mode, as well as leaving timers and CPU operating, Idle mode is no longer recommended for new
designs, and is included for backward software compatibility only.
STOP MODE
Setting the STOP bit of the Power Control register (PCON.1) invokes Stop mode. Stop mode is the
lowest power state (besides power off) since it turns off all internal clocking. The I
CC
of a standard Stop
mode is approximately 1
μ
A (consult the Electrical Specifications section for full details). All processor
operation ceases at the end of the instruction that sets the STOP bit. The CPU can exit Stop mode via an
external interrupt, if enabled, or a reset condition. Internally generated interrupts (timer, serial port,
watchdog) cannot cause an exit from Stop mode because internal clocks are not active in Stop mode.
BAND-GAP SELECT
The DS80C390 provides two enhancements to Stop mode. As described below, the device provides a
band-gap reference to determine Power-fail Interrupt and Reset thresholds. The band-gap reference is
controlled by the Band-Gap Select bit, BGS (RCON.0). Setting BGS to a 1 will keep the band-gap
reference enabled during Stop mode. The default or reset condition of the bit is logic 0, which disables
the band-gap during Stop mode. This bit has no control of the reference during full power, PMM, or Idle
modes.
With the band-gap reference enabled, the Power-fail reset and interrupt are valid means for leaving Stop
mode. This allows software to detect and compensate for a power supply sag or brownout, even when in
Stop mode. In Stop mode with the band-gap enabled, I
CC
will be approximately 100
μ
A compared with 1
μ
A with the band-gap disabled. If a user does not require a Power-fail Reset or Interrupt while in Stop
mode, the band-gap can remain disabled. Only the most power sensitive applications should disable the
band-gap reference in Stop mode, as this results in an uncontrolled power down condition.
RING OSCILLATOR
The second enhancement to Stop mode reduces power consumption and allows the device to restart
instantly when exiting Stop mode. The ring oscillator is an internal clock that can optionally provide the
clock source to the microcontroller when exiting Stop mode in response to an interrupt.
相關PDF資料
PDF描述
DS80C410 Network Microcontrollers with Ethernet and CAN
DS80C410-FNY Network Microcontrollers with Ethernet and CAN
DS80C411-FNY Network Microcontrollers with Ethernet and CAN
DS8187
DS850-3 850 Watts 12V
相關代理商/技術參數
參數描述
DS80C390-QCR+ 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C390-QNR 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C390-QNR+ 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_03 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*