參數資料
型號： DS80C390-QNR
元件分類： 微處理器
英文描述： Dual CAN High-Speed Microprocessor
中文描述： 雙CAN高速微處理器
文件頁數： 12/58頁
文件大?。?/td> 5486K
代理商： DS80C390-QNR
DS80C390
12 of 58
110199
MEMORY ADDRESSING
The DS80C390 incorporates three internal memory areas:
§
256 bytes of scratchpad (or direct) RAM
§
4 KB of SRAM configurable as various combinations of MOVX data memory, stack memory, and
MOVC program memory
§
512 bytes of RAM reserved for the CAN message centers.
Up to 4 MB of external memory is addressed via a multiplexed or demultiplexed 20-bit address bus/8-bit
data bus and four chip enable (active during program memory access) or four peripheral enable (active
during data memory access) signals.
Three different addressing modes are supported, as selected by the AM1, AM0 bits in the ACON SFR.
16-bit address mode
16-bit address mode accesses memory similarly to the traditional 8051. It is opcode compatible with the
8051 microprocessor and identical to the byte and cycle count of the Dallas Semiconductor High-Speed
Microcontroller family. A device operating in this mode can access up to 64 KB of program and data
memory. The device defaults to this mode following any reset.
22-bit paged address mode
The 22-bit paged address mode retains binary code compatibility with the 8051 instruction set, but adds
one machine cycle to the ACALL, LCALL, RET and RETI instructions with respect to the Dallas
Semiconductor High-Speed Microcontroller family timing. This is transparent to standard 8051
compilers. Interrupt latency is also increased by one machine cycle. In this mode, interrupt vectors are
fetched from 0000xxh.
22-bit contiguous address mode
The 22-bit contiguous addressing mode uses a full 22-bit program counter, and all modified branching
instructions automatically save and restore the entire program counter. The 22-bit branching instructions
such as ACALL, AJMP, LCALL, LJMP, MOV DPTR, RET and RETI instructions require an assembler,
compiler and linker that specifically supports these features. The INC DPTR is lengthened by one cycle
but remains byte count compatible with the standard 8051 instruction set.
Internally, the device uses a 22-bit program counter. The lowest order 22 bits are used for memory
addressing, with a special 23
rd
bit used to map the 4KB SRAM above the 4 MB memory space in
bootstrap loader applications. Address bits 16-23 for the 22-bit addressing modes are generated via
additional SFRs dependent on the type of instruction as shown below.
EXTENDED ADDRESS GENERATION:
Table 2
Address bits 23-16
DPX;93h
DPX1;95h
MXAX;EAh
AP;9Ch
Address bits 15-8
DPH;83h
DPH1;85h
P2;A0h
--
Address bits 7-0
DPL;82h
DPL1;84h
Ri
--
MOVX instructions using DPTR
MOVX instructions using DPTR1
MOVX instructions using @Ri
Addressing program memory in
22-bit paged mode
10-bit stack pointer mode
--
ESP;9Bh
SP;81h
相關PDF資料
PDF描述
DS80C390-FCR Dual CAN High-Speed Microprocessor
DS80C390-FNR Dual CAN High-Speed Microprocessor
DS80C390-QCR Dual CAN High-Speed Microprocessor
DS80C410 Network Microcontrollers with Ethernet and CAN
DS80C410-FNY Network Microcontrollers with Ethernet and CAN
相關代理商/技術參數
參數描述
DS80C390-QNR+ 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_03 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_07 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_09 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*