參數資料
型號： DS80C390-QNR
元件分類： 微處理器
英文描述： Dual CAN High-Speed Microprocessor
中文描述： 雙CAN高速微處理器
文件頁數： 18/58頁
文件大?。?/td> 5486K
代理商： DS80C390-QNR
DS80C390
18 of 58
110199
SYSTEM CLOCK CONFIGURATION
Table 10
CD1
CD0
2X
4X/
0
0
0
Frequency Multiplier (2X)
0
0
1
Frequency Multiplier (4X)
0
1
N/A
Reserved
1
0
N/A
Divide-by-four (Default)
1
1
N/A
Power Management Mode
Name
Clocks/MC
2
1
Max. External Frequency
20 MHz
10 MHz
4
40 MHz
40 MHz
1024
The system clock and machine cycle rate changes one machine cycle after the instruction changing the
control bits. Note that the change will affect all aspects of system operation, including timers and baud
rates. The use of the switchback feature, described later, can eliminate many of the problems associated
with the Power Management Mode.
Changing the system clock/machine cycle clock frequency
The microcontroller incorporates a special locking sequence to ensure “glitch-free” switching of the
internal clock signals. All changes to the CD1, CD0 bits must pass through the 10 (divide-by-four) state.
For example, to change from 00 (frequency multiplier) to 11 (PMM), the software must change the bits in
the following sequence: 00 -> 10 -> 11. Attempts to switch between invalid states will fail, leaving the
CD1, CD0 bits unchanged.
The following sequence must be followed when switching to the frequency multiplier as the internal time
source. This sequence can only be performed when the device is in divide-by-four operation. The steps
must be followed in this order, although it is possible to have other instructions between them. Any
deviation from this order will cause the CD1, CD0 bits to remain unchanged. Switching from frequency
multiplier to non-multiplier mode requires no steps other than the changing of the CD1, CD0 bits.
1.
Ensure that the CD1, CD0 bits are set to 10, and the RGMD (EXIF.2) bit = 0.
2.
Clear the CTM (Crystal Multiplier Enable) bit.
3.
Set the
2X
4X/
bit to the appropriate state.
4.
Set the CTM (Crystal Multiplier Enable) bit.
5.
Poll the CKRDY bit (EXIF.4), waiting until it is set to 1. This will take approximately 65536 cycles
of the external crystal or clock source.
6.
Set CD1, CD0 to 00. The frequency multiplier will be engaged on the machine cycle following the
write to these bits.
OSCILLATOR FAIL DETECT
The microprocessor contains a safety mechanism called an on-chip Oscillator Fail Detect circuit. When
enabled, this circuit causes the processor to be held in reset if the oscillator frequency falls below TBD
kHz. In operation, this circuit complements the Watchdog timer. Normally, the watchdog timer is
initialized so that it will time-out and will cause a processor reset in the event that the processor loses
control. In the event of a crystal or external oscillator failure, however, the watchdog timer will not
function and there is the potential for the processor to fail in an uncontrolled state. The use of the
oscillator fail detect circuit forces the processor to a known state (i.e., reset) even if the oscillator stops.
The oscillator fail detect circuitry is enabled when software sets the enable bit OFDE (PCON.4) to a 1.
Please note that software must use a “Timed Access” procedure (described later) to write this bit. The
OFDF (PCON.5) bit will also be set to a 1 when the circuitry detects an oscillator failure, and the
processor is forced into a reset state. This bit can only be cleared to a 0 by a power fail reset or by
software. The oscillator fail detect circuitry will not be activated when the oscillator is stopped due to the
processor entering Stop mode.
相關PDF資料
PDF描述
DS80C390-FCR Dual CAN High-Speed Microprocessor
DS80C390-FNR Dual CAN High-Speed Microprocessor
DS80C390-QCR Dual CAN High-Speed Microprocessor
DS80C410 Network Microcontrollers with Ethernet and CAN
DS80C410-FNY Network Microcontrollers with Ethernet and CAN
相關代理商/技術參數
參數描述
DS80C390-QNR+ 功能描述:8位微控制器 -MCU Dual CAN High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_03 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_07 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
DS80C400_09 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*