參數資料
型號: DS80C410-FNY
英文描述: Network Microcontrollers with Ethernet and CAN
中文描述: 網絡微控制器與以太網和CAN
文件頁數: 25/102頁
文件大?。?/td> 2637K
代理商: DS80C410-FNY
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
25 of 102
OWSTP
PIN TIMING CHARACTERISTICS
(V
CC3
= 3.0V to 3.6V, V
CC1
= 1.8V ±10%, T
A
= -40°C to +85°C.) (Note 1)
STANDARD
MIN
6.4
OVERDRIVE
MIN
0.8
PARAMETER
SYMBOL
MAX
8
MAX
1
UNITS
Active Time for Presence Detect
t
ON1
s
Active Time for Presence Detect Recovery
t
ON2
8
10
8
10
s
Active Time for Write 1 Recovery (Notes 2, 3)
t
ON3
51.2
64
7.2
9
s
Active Time for Write 0 Recovery (Notes 2, 3)
t
ON4
6.4
8
0.8
1
s
Delay Time for Presence Detect
t
DLY1
0.8
1
0.8
1
s
Delay Time for Presence Detect Recovery (Note 4)
t
DLY2
399.2
499
31.2
39
s
Delay Time for Write 1/Write 0 Recovery
t
DLY3
0.8
1
0.8
1
s
Turn-Off Time for 1-Wire Reset
t
OFF1
1.6
2
1.6
2
s
Turn-Off Time for Write 1/Write 0 (Note 5)
t
OFF2
0.8
1
0.8
1
s
Note 1:
AC electrical characteristics assume 50% duty cycle for the oscillator, oscillator frequency
75MHz, and are not 100% production
tested, but are guaranteed by design.
There is no
OWSTP
timing difference for sending out and receiving bits within a byte. The difference comes when the last bit of the
byte has been completely sent. At this point, the signal is either enabled continuously until the next reset or time slot begins, or
enabled only for active time write 1 or write 0.
When performing a read versus a write time slot, the master provides the same active time for write 1 and write 0. However, the
Schmitt-triggered input from the OW line is sensed every 1 s for a high value. If OW is high, the
OWSTP
signal is enabled. If the OW
line is low, the
OWSTP
signal remains disabled until a high state is sensed. In all write time slots, a high is sensed immediately.
This parameter is the time delay until the master begins to monitor the OW pin level. If the line is already high, then
OWSTP
is
enabled. If not, it waits to enable
OWSTP
until the next state machine clock (1 s or 50ns) after the OW line recovers.
The very first bit in a byte has an extended turn-off time of 4 s because of the order of states that the 1-Wire master state machine
must go through.
Note 2:
Note 3:
Note 4:
Note 5:
OWSTP PIN TIMING
相關PDF資料
PDF描述
DS80C411-FNY Network Microcontrollers with Ethernet and CAN
DS8187
DS850-3 850 Watts 12V
DS850-9 850 Watts 48V Distributed Power System
DS8617
相關代理商/技術參數
參數描述
DS80C410-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C411 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Network Microcontrollers with Ethernet and CAN
DS80C411-FNY 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C411-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80CH11 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager