- 您現在的位置：買賣IC網 > PDF目錄1916 > DS8113-JNG+ (Maxim Integrated Products)IC INTERFACE SMART CARD 28-TSSOP PDF資料下載
參數資料
| 型號： | DS8113-JNG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE SMART CARD 28-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 241 |
| 應用： | 智能卡 |
| 接口： | 模擬 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
Smart Card Power Select
The DS8113 supports three smart card VCC voltages:
1.8V, 3V, and 5V. The power select is controlled by the
1_8V and 5V/3V signals as shown in Table 3. The 1_8V
signal has priority over 5V/3V. When 1_8V is asserted
high, 1.8V is applied to VCC when the smart card is
active. When 1_8V is deasserted, 5V/3V dictates VCC
power range. VCC is 5V if 5V/3V is asserted to a logic-
high state, and VCC is 3V if 5V/3V is pulled to a
logic-low state. Care must be exercised when switching
from one VCC power selection to the other. If both 1_8V
and 5V/3V are high with CMDVCC high at the same
time, the DS8113 enters stop mode. To avoid acciden-
tal entry into stop mode, the state of 1_8V and 5V/3V
must not be changed simultaneously. A minimum delay
of 100ns should be observed between changing the
states of 1_8V and 5V/3V. See Figure 9 for the recom-
mended sequence of changing the VCC range.
DS8113
Smart Card Interface
______________________________________________________________________________________
15
VCC SELECT
STOP MODE
1.8V
3V
5V
1_8V
5V/3V
CMDVCC
Figure 9. Smart Card Power Select
Table 3. VCC Select and Operation Mode
1_8V
5V/3V
CMDVCC
VCC SELECT (V)
CARD INTERFACE STATUS
0
3
Activated
0
1
3
Inactivated
0
1
0
5
Activated
0
1
5
Inactivated
1
0
1.8
Activated
1
0
1
1.8
Inactivated
1
0
1.8
Reserved (Activated)
1
1.8
Not Applicable—Stop Mode
相關PDF資料 |
PDF描述 |
|---|---|
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
| DS87C530-ECL+ | IC MCU EPR/ROM W/RTC 33MZ 52TQFP |
| DS87C530-KCL | IC MCU EPR/ROM W/RTC 33MZ 52CLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS8113-JNG+ | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS8113-JNG+T&R | 制造商:Maxim Integrated Products 功能描述:DS8113 SMARTCARD INT 28 TSSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-TSSOP |
| DS8113-JNG+T&R | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS8113-KIT | 制造商:Maxim Integrated Products 功能描述:EMV EVALUATION KIT FOR THE DS8113 - Boxed Product (Development Kits) |
| DS8113-RNG+ | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。