參數資料
型號： DS89C450-ENG
廠商： Maxim Integrated Products
文件頁數： 15/46頁
文件大?。?/td> 0K
描述： IC MCU FLASH 64KB 25MHZ 44-TQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
產品變化通告： Product Discontinuation 20/Feb/2012
標準包裝： 160
系列： 89C
核心處理器： 8051
芯體尺寸： 8-位
速度： 25MHz
連通性： EBI/EMI，SIO，UART/USART
外圍設備： 電源故障復位，WDT
輸入/輸出數： 32
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 托盤
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
22 of 46
fetch that takes four clocks. Page mode 1 is the only external addressing mode where the CPU does not require
stalls for external memory access, but page misses result in reduced external access performance.
On-Chip Program Memory
The processor can fetch the entire on-chip program memory range automatically. By default, the reset routines and
all interrupt vectors are located in the lower 128 bytes of the on-chip program memory.
On-chip program memory is logically divided into pairs of 8kB, 16kB, or 32kB flash memory banks to support in-
application programming. The upper block of the on-chip program memory is designed to be programmed in-
application with the standard 5V VCC supply under the control of the user software or by using a built-in program
memory loader. It can also be programmed in standard flash or EPROM programmers. The DS89C430
incorporates a memory management unit (MMU) and other hardware to support any of the three programming
methods. The MMU controls program and data memory access, and provides sequencing and timing controls for
programming of the on-chip program memory. A separate security flash block supports a three-level lock, a 64-byte
encryption array, and other flash options.
Security Features
The DS89C430 incorporates a 64-byte encryption array, allowing the user to verify program codes while viewing
the data in encrypted form. The encryption array is implemented in a security flash memory block that has the
same electrical and timing characteristics as the on-chip program memory. Once the encryption array is
programmed to non-FFh, the data presented in the verify mode is encrypted. Each byte of data is XNORed with a
byte in the encryption array during verification.
A three-level lock restricts viewing of the internal program and data memory contents. By programming the three
lock bits, the user can select a level of security as specified in Table 3. The protection levels function differently
than those in a traditional 8051 microcontroller, and should not be used while executing external code.
Once a security level is selected and programmed, the setting of the lock bits remains. Only a mass erase can
erase these bits and allow reprogramming the security level to a less restricted protection.
Table 3. Flash Memory Lock Bits
LEVEL
LB1
LB2
LB3
PROTECTION
1
No program lock. Encrypted verify if encryption array is programmed. Do
not execute external program code while operating at this security level.
2
0
1
Prevent MOVC in external memory from reading program code in internal
memory. EA is sampled and latched on reset. Allow no further parallel or
program memory loader programming. Do not execute external program
code while operating at this security level.
3
X
0
1
Level 2 plus no verify operation. Also prevent MOVX in external memory
from reading internal SRAM. Do not execute external program code while
operating at this security level.
4
X
0
Level 3 plus no external execution.
The DS89C430 provides user-selectable options that must be set before beginning software execution. The option
control register uses flash bits rather than SFRs, and is individually erasable and programmable as a byte-wide
register. Bit 3 of this register is defined as the watchdog POR. Setting this bit to 1 disables the watchdog reset
function on power-up. Clearing this bit to 0 enables the watchdog reset function automatically. Other bits of this
register are undefined and are at logic 1 when read. The value of this register can be read at address FCh in
parallel programming mode or executing a verify-option-control register instruction in ROM loader mode or in-
application programming mode.
相關PDF資料
PDF描述
DS89C440-QNL IC MCU FLASH 32KB 33MHZ 44-PLCC
DS89C440-QNG IC MCU FLASH 32KB 25MHZ 44-PLCC
DS89C440-MNL IC MCU FLASH 32KB 33MHZ 40-DIP
DS89C440-MNG IC MCU FLASH 32KB 25MHZ 40-DIP
DS89C440-ENL IC MCU FLASH 32KB 33MHZ 44-TQFP
相關代理商/技術參數
參數描述
DS89C450-ENG+ 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS89C450-ENL 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS89C450-ENL+ 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS89C450-K00 功能描述:開發板和工具包 - 8051 RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
DS89C450-KIT# 功能描述:開發板和工具包 - 8051 Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*