- 您現在的位置：買賣IC網 > PDF目錄3787 > DS89C450-ENG (Maxim Integrated Products)IC MCU FLASH 64KB 25MHZ 44-TQFP PDF資料下載
參數資料
| 型號： | DS89C450-ENG |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/46頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU FLASH 64KB 25MHZ 44-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 160 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 25MHz |
| 連通性： | EBI/EMI，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-TQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
24 of 46
Table 4. In-Application Programming Commands
FC3:FC0
COMMAND
OPERATION
0000
Read Mode
Default state. All flash blocks are in read mode.
Note: The upper bank
of flash memory is inaccessible for execution unless the FC3:0 bits are
in the read mode (0000b) state.
0001
Verify Option Control Register
Read data from the option control register. Data is available in the
FDATA at the end of the following machine cycle. FDATA.3 is the logic
value of the watchdog POR default setting.
0010
Verify Security Block
Read a byte of data from the security block. After the address byte is
written to the FDATA, data is available in the FDATA at the end of the
following machine cycle. (Lock bits are addressed at 40h and
FDATA.5:3 are the logic value of LB1, LB2 and LB3, respectively.)
0011
Verify Upper Program
Memory Bank
Read a byte of data from upper flash memory bank (address range
from 2000h to 3FFFh). The first and second byte writes to the FDATA
are the upper and lower byte of the address. Data is available in the
FDATA at the end of the following machine cycle after the second
address byte is written.
0100
Reserved for Future Use
This command should not be modified by user programs.
1000
Reserved for Future Use
This command should not be modified by user programs.
1001
Write Option Control Register
Write to the option control register as data is written to FDATA. Bit 3 of
the data byte represents the watchdog POR default setting.
1010
Write Security Block
Write a byte of data to the security block at a selected locations
addressed by the first byte write to the FDATA. The second write to the
FDATA is the data byte. (Lock bits are addressed at 40h and the
FDATA 5:3 represents lock bits LB3, LB2, and LB1, respectively.)
1011
Write Upper Program
Memory Bank
Write a byte of code to the upper flash memory bank (address range
from 2000h to 3FFFh). The first and second byte writes to the FDATA
are the upper byte and the lower byte of the address. The third write to
the FDATA is the data byte.
1100
Erase Option Control Register
Erase the option control register. The contents of this register are
returned to FFh. This operation disables the watchdog reset function on
power-up.
1101
Erase Security Block
Erase the security flash block that contains the 64-byte encryption array
and the lock bits. The content of every memory location is turned into
FFh.
1110
Erase Upper Program
Memory Bank
Erase the upper bank of flash memory bank. The contents of every
memory location are returned to FFh.
1111
System Reset
This command is used to cause a system reset.
The flash command bits are cleared to 0 on all forms of reset, and it is important for the user software to clear
these bits to 0 to return the flash memory to read mode from erase/program operation. This setting is a “no
operation” condition for the MMU, which allows the processor to return to its normal execution. Note that the busy
and error flags have no function in normal flash-read mode.
The FCNTL SFR can only be written using timed access. This procedure provides protection against inadvertent
erase/program operation on the flash memory. Any command written to the FCNTL during a flash operation is
ignored (FBUSY = 0). To ensure data integrity, an erase command sequence should be reinitiated if an erase or
program operation is interrupted by a reset.
相關PDF資料 |
PDF描述 |
|---|---|
| DS89C440-QNL | IC MCU FLASH 32KB 33MHZ 44-PLCC |
| DS89C440-QNG | IC MCU FLASH 32KB 25MHZ 44-PLCC |
| DS89C440-MNL | IC MCU FLASH 32KB 33MHZ 40-DIP |
| DS89C440-MNG | IC MCU FLASH 32KB 25MHZ 40-DIP |
| DS89C440-ENL | IC MCU FLASH 32KB 33MHZ 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS89C450-ENG+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS89C450-ENL | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS89C450-ENL+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS89C450-K00 | 功能描述:開發板和工具包 - 8051 RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| DS89C450-KIT# | 功能描述:開發板和工具包 - 8051 Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。